You can also change fan speed with the remote and these range from one (which is virtually silent) to ten and are indicated on the circular OLED status panel set into the base. Dip a soft cloth into the warm soapy water and squeeze out the excess water,' says Felix Wilson, Cleaning Expert, Unclutterer. 'Wipe each blade carefully, and use a soft brush to clean the hard-to-reach areas.' Note that devices like the Dyson Hot+Cool range often also clean the air as they work, so you should also make sure you're cleaning/changing the filter as needed. The dust has to go somewhere! How to clean a tower fan If you were the one who assembled it in the first place, then it should be simple to simply reverse this process. However, if the fan arrived in its full form, make sure you know what you're doing. Taking apart your fan can also affect your warranty, so consider this before doing anything.

Floor fans are larger, more powerful and are designed to fill a bigger space. As they’re designed to be used at a distance, they might offer more angles, a wider oscillation range and a remote control. This is handy if you want to turn the fan up or down from the bed or even just pause it while you take a phone call. Otherwise, they’re very similar to desk fans and have the same kind of features – in fact, there’s plenty of overlap between the two. You can change the direction of this airflow up and down by sliding the dome part up and down, and the fan can also be set to oscillate automatically using the small remote control that attaches magnetically to the front panel. If your fan's grill is suitable for washing, then this will undoubtedly be the most efficient way to get to everything in the nooks and crannies.Assembly is easy, and connecting it to your smartphone and Wi-Fi network using the GeoSmartPro app is a simple enough process. From there, you can create daily schedules, preset modes and even auto-modes that will switch the fan on to a custom setting when specific weather conditions are met. It’s also compatible with Alexa and Google Home devices, although you can’t alter as many settings using your voice as you can when using the app or physical controls. You may still need to go in with a microfibre cloth after this. We recommend dipping your cloth in soapy water - without using an excessive amount - and wiping down all the fan's components to remove every last trace of dust. It’s a similar story with pedestal fans, which are basically more powerful desk fans on a stand that are designed to cool a larger area. You can usually adjust the height, pivot and oscillation to control airflow, but they tend to be bulkier than tower fans so you’ll need to make sure you have enough space – both for use and for storage. Spray the air into the blades of the fan; the nozzle should reach between the grills so you don't have to take it all apart. This will effectively remove all the dust and dirt that is hiding inside your fan. You could even use a hairdryer if you don't want to buy a can of compressed air.

If you're feeling confident, the face and rear grills of your fan are likely to be secured with some screws (don't lose these!). Place the fan face down on a flat surface and carefully remove the screws to access the blades. This will help prevent the screws from falling inside the fan. Again, make sure not to get any part of the fan that's connected to the electricals or motor wet, and leave everything to dry thoroughly before reassembling. If you're happy, then gently wash the grill over the sink with a sponge. 5. Reassemble For how to clean a fan without blades, you just need to get a damp cloth and give it a good wipe down. It's just like cleaning any of your appliances, like the best kettles.You will need a can of compressed air and blow it into the vent to release clogged dust or dirt,' says Andrew. 'Finally use a duster to remove any remaining dirt off the fan.' Then give the stand a wipe down with a microfibre cloth. Do this every three to four weeks, or more if you're using the fan daily. Fans aren’t generally that expensive to run – even the most powerful models we’ve tested use around 40W when running at maximum speed. However, the most energy-efficient models we’ve tested consume under 20W at full blast and less than 5W at their lowest speed, which could make a difference to your bills if you’re running the fan all summer long. You can also keep your costs low by using any timer features, which can be set to shut the fan off after a set period. We’ve even seen some fans that can regulate their speed according to the ambient temperature, or that have a sleep setting where the fan slows down gradually over the course of the night. While it’s one of the taller tower fans we’ve tested, it’s worth making room for Levoit’s 36-inch Tower Fan. Look beyond the two-part plastic base and it’s a well-built unit with no hint of wobble, with stylish and straightforward touch controls on the top panel. It also has some useful advanced features, including an Auto mode that adjusts the speed according to the room temperature, and a Sleep mode that will do its best to keep you cool while staying quiet. There’s also a Turbo mode for some extra speed, plus a simple one to 12-hour off timer.However, what we like most about this tower fan is that it offers an efficient and economical way to cool a larger area. It pushes through air at speeds of up to 3.2m/sec at the highest of its five speed settings, or 3.3m/sec in Turbo mode. True, it’s a little loud when maxed out, at 44.4 to 45.2dB, but on its next to lowest setting you can still hit speeds of 2.1m/sec, with the noise reduced to around 32dB. On its lower settings it uses only around 20W as well. Throw in the competitive price, and you have a great tower fan for bigger rooms. Key specs – Dimensions: 77.3 x 28.8 x 29.3cm; Weight: 5.1kg; Oscillation angle: 90 degrees (horizontal), 60 degrees (vertical) Cord length: 1.6m; Warranty: 2yrs; Power: 20W