A list of available device paths can be found in Settings > System > Hardware> dot menu> All Hardware. MetaGeek Support has a good reference article about channel selection for Zigbee and WiFi coexistance. FYI, ITead just released a new “ZBDongle-E” adapter as an improved replacement for ITead’s previous barebone Silabs EFR32MG21 adapter and an alternative to ITead’s TI CC2652P based “Sonoff Zigbee 3.0 USB Dongle Plus” (as Silicon Lab and Texas Instruments adapters offer different compatibility).

Zigbee and Z How to Transform a RaspberryPi Into a Universal Zigbee and Z

Note that not all configuration parameters are available with all coordinators. # Link Key (zigbee_linkkey) Home Assistant’s ZHA integration supports all standard Zigbee device types. It should be compatible with most Zigbee devices as long as they fully conform to the official ZCL (Zigbee Cluster Library) specifications defined by the CSA (Connectivity Standards Alliance, formerly the Zigbee Alliance). There is therefore no official compatibility list of devices that will work out-of-the-box with the ZHA integration. Telegesis ETRX357USB/ETRX357USB-LR/ETRX357USB-LRS+8M (Note! These first have to be flashed with other EmberZNet firmware)

Target Applications

Unplug your old radio will inform you that your old Zigbee coordinator radio has been reset and that you can now plug in your new Zigbee coordinator radio adapter.

Adapter settings | Zigbee2MQTT Adapter settings | Zigbee2MQTT

The install code must be entered into the coordinator settings before starting the discovery process. Be sure to fill out Home Assistant SkyConnect interest form so they know how many they should make: Be patient as the pairing of some Zigbee devices may require multiple attempts and you may sometimes need to try again and again.I read now however that they will initially only ship it with Zigbee support, and that Thread support will come later via firmware and software updates. For example, interference from USB 3.x ports, unshielded USB 3.x devices, and non-shielded USB 3.x peripheral cables are especially infamously known to affect 2.4 GHz radio reception for low-power/low-bandwidth devices. Therefore you should always place your Zigbee adapter far away as possible from any potential sources of EMI/EMI/RMI, preferably by using an adequately long shielded USB extension cable connected to a USB 2.0 port. PS: EFR32MG21 is by the way the same Silabs radio MCU SoC radio chip used in " ITead Sonoff Zigbee 3.0 USB Dongle Plus V2” (model “ZBDongle-E”) and their previous ITead Zigbee 3.0 USB Dongle (Model: 9888010100045). More information about those competing and possibly compatible adapters here:

Review of Sonoff ZIGBEE 3.0 USB DONGLE PLUS - Reddit Review of Sonoff ZIGBEE 3.0 USB DONGLE PLUS - Reddit

CC2652P2 ZigBee Ethernet Coordinator, ethernet part based on USR-K6 open in new window module. POE possible with external splitter. Comes complete with 3d printed case and antenna. Dongle firmware can be upgraded using the openHAB console with the zigbee firmware command. The firmware file must be specified next. The dongle will be taken offline, put into firmware upgrade mode and then upgraded. You MUST ensure that you have the correct firmware for your dongle as programming the incorrect firmware can render the device inoperable - requiring a programmer to recover. # Flashing/Upgrading on Linux Start a warning using both strobe signal and siren (type 'burglar alarm'), with a duration of 30 seconds. Note: Currently only Ember coordinators support Zigbee 3.0, it does not look like the Telegesis coordinators will receive an update to support it.

Success!

The syntax for the command strings is as in the examples above, where the possible values for type, useStrobe, warningMode, squawkMode, sirenLevel, squawkLevel, and duration are as follows: Command parameter If you are running a Zigbee2MQTT network, you need to stop the add-on and change the configuration to access the new multiprotocol firmware Note: cluster_id: 25 may also be cluster_id: 0x0019. The two are synonymous. Defining Zigbee channel to use You can also configure the coordinator via an old style Things file. Things files should be placed in OPENHAB_CONF/things. Here are some examples for a coordinator congiguration in a .things file. Online OTA providers for firmware updates are currently only available for IKEA, LEDVANCE/OSRAM, SALUS/Computime, and INOVELLI devices. Support for OTA updates from other manufacturers could be supported in the future if they publish their firmware images publicly.