The pressure the spring exerts is strong enough to enable the staple to penetrate even hard materials. Safety First: Unplug the staple gun if it's electric or disconnect it from the air supply if it's pneumatic. She has been featured in multiple publications including Better Homes and Gardens and Make Magazine. Hold the release button between your thumb and forefinger and push the magazine back into the compartment. Electric Staple Guns: These are powered by electricity through a cord plugged into an outlet or a rechargeable battery.

This article has been fact-checked, ensuring the accuracy of any cited facts and confirming the authority of its sources. Hold the rod straight and push it into the chamber, hooking the back of the rod in place at the top or bottom.Squeeze the lever at the front of the gun, and pull the rod away from the stapler to remove the magazine. Adjust the depth setting on your staple gun to ensure it's set correctly for the material you're working with. Misuse: Applying too much force when using the staple gun, or using it on inappropriate materials, can cause jams. Then, place the front of the gun on a piece of wood pull the trigger to ensure that only 1 staple comes out of the gun at a time.

Remove Jammed Staples: If a jammed staple is causing the issue, use needle-nose pliers or a flathead screwdriver to remove it carefully. The lightweight handle has a reduced head-to-shaft ratio, making striking and fixing easier and using less effort. Take a row of staples and position them so that the legs are facing down with the staples on top of the rails inside of the chamber. Use your hand to slide them up and down on the rail to ensure that they can move freely without getting caught on the rail. Dirt and debris: Over time, dust, grime, or small fragments of staples can accumulate in the staple gun, causing it to jam.Clean and lubricate it regularly, and inspect it for any signs of wear or damage that could affect its functionality. Pull the plug out of the wall, and find the trigger lock just behind the trigger that you would use to release a staple. To make sure the staples are loaded properly, fold a piece of paper in half or use a scrap piece of wood or fabric. Disconnect the stapler by switching the power button on the back of the compressor tank to the “off” position.

By considering these factors, you can ensure you're choosing a staple gun that delivers the best performance for your specific needs. The heads are made of premium steel and have a length of 80 or 100 mm, depending on the size and all in a sturdy storage case. If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. If you're going to be using a lot of staples for the project, it's a good idea to fill up the chamber with staples, leaving only about 1⁄ 4 in (0. Most pneumatic staple guns have a large one at the front of the gun, protruding from underneath the area where the staples fire out of the gun.Staple misfires occur when the staple gun fails to drive staples into the material, leaving them partially or fully sticking out. Remember to handle your tools safely and responsibly, and never force a stuck mechanism, as it can cause further damage. Consider the nature of your tasks, the materials you'll be working with, and your workspace when choosing the right tool. If you notice that your staple gun is not providing enough power to drive staples into materials effectively, there might be an issue with its stapling power.

It comes with 12 interchangeable heads that can handle various screw types including Slotted, Phillips, Pozidriv, and Star. Once the trigger is released, the spring retracts, pulling the rod back and setting the next staple in place for use. Constantly adjust the knob carefully and test the staple gun on a scrap piece of material first to ensure you've set the correct force for your project. We act as a credit broker not a lender, offering credit products provided exclusively by Klarna Bank AB UK branch (BR020956), a branch of Klarna AB (556737-0431) which is authorised and regulated by the Swedish Financial Services Authority. Consider a model with an adjustable power control feature, allowing you to control the force of the staple being fired, which can be critical for different materials.Use your hand to loosen the nut on the bottom of the gun to disconnect it from the hose that attaches it to the compressor. This straightforward but effective mechanism allows for rapid, efficient stapling, making the staple gun a vital tool in various applications, from upholstery work to construction projects.