Another benefit that DALY has is that they are totally sealed. You are not getting into that BMS. Nothing is exposed and it is very, very well-built. In fact, the DALY BMS has the highest build quality out of them all as they are totally sealed and even waterproof. The one downside to this is their BMSs can be rather large and clunky. Do not leave your BMS in direct sunlight or exposed to any heat source, your BMS should be stored in an ambient temperature of -5°C~+40°C, and a relative humidity of not more than 70%. is OK for charging its on the low side but best to leave it alone for now and get the BMS set up correctly. At present the BMS is incorrect.

A few things that do NEED Clarification for your own sanity and because there are LEADisms and Wives Tales associated with them due to misunderstandings. This BMS has a continuous discharge current of 100A and a peak current of 165A to 200A, which is simply an insane amount of power. This BMS has settings to adjust the overcharge and over-discharge protection levels, which is super nice. I cannot stress enough how easy it is to use the JK BMS app. Everything is where you expect it to be, and everything makes sense. The "Allowable Voltage Range" for LFP starts at 2.500 and ends at 3.650 Volts per cell. There is No Harm/Damage cause when the cells remain in that range. Go Above or Below and you're causing harm. LFP Has a Low Internal Resistance compared to others and as such can put out a LOT of juice in a burst. JK BMS is great. The BMS themselves are very well built and the app is well designed. The menus in the JK BMS app are laid out intuitively, which makes the app super easy to use. Another important thing is that I have never experienced any sort of connection issues when communicating with a JK BMS over Bluetooth.All JK-BMS models with software version >=6.0 are using the implemented protocol and should be supported. Equalizer power supply, can be connected to the postive for any section of 13~24S ;can also be connected to a 40-100V DC External power supply. a) Before touching the PCB, the person performing the operation must discharge static electricity and take anti-static measures;

sensor:127]: 'jk-bms power tube temperature recovery': Sending state 70.00000 °C with 0 decimals of accuracy sensor:127]: 'jk-bms total charging cycle capacity': Sending state 0.00000 with 0 decimals of accuracy sensor:127]: 'jk-bms temperature sensor temperature recovery': Sending state 100.00000 °C with 0 decimals of accuracy When the voltage is lower than 40V, the equalizer needs to provide external DC 40V~100V power supply.

Overview

The BMS is not supposed to CYCLE, its a protection device not a control device. The concept is the same as the breakers in your load panel. They don't cycle on and off, you turn your appliances on and off as needed. The breaker only TRIPS if there is a short circuit. Our warranty does not cover items that have been damaged due to gross negligence, normal wear and tear, damage due to accident or collision, abuse or incorrect installation.

Bluetooth communication function, equipped with APP, to view the state of the battery in real time; c) When performing welding work on the equalizer, make sure that the soldering iron tip is grounded; Now I am looking at 123SmartBMS that is integrated with Victron by installing software into the root of the Cerbo.

Technical Specifications

sensor:127]: 'jk-bms temperature sensor temperature difference protection': Sending state 20.00000 °C with 0 decimals of accuracy sensor:127]: 'jk-bms temperature sensor temperature protection': Sending state 100.00000 °C with 0 decimals of accuracy sensor:127]: 'jk-bms power tube temperature protection': Sending state 90.00000 °C with 0 decimals of accuracy sensor:127]: 'jk-bms total voltage overvoltage protection': Sending state 5.46000 V with 3 decimals of accuracy I don't think jblance's program does any programming. I can't remember, but doesn't the default app have provisions to set a voltage? I thought there's a low voltage setting where it will stop balancing once it reaches a low voltage limit. So you can set it to 4.0V so it will never balance until it gets over that value. Oh I just noticed that you have the BMS version, which may have a different interface?