Once the fans are connected to the lighting hub, lighting node pro, and your PC, the next step is setting up the software for your fans. You can do that by following the steps listed below: The main difference between LL120 vs ML120 is that the ML120 uses premium magnetic levitation technology to provide users with excellent performance at low noise while the LL120 uses hydraulic bearing technology and has a light loop that’s sure to improve the aesthetics of your rig. What Is LL120 Fan Best For? Created for Quiet:>/b> 120mm Fan blade engineered for low-noise operation without sacrificing performance Please enter your motherboard BIOS and set the correspondent fan header at PWM mode. (Update your motherboard BIOS if necessary)

The ML120s are also fans that support the PWM technology, which means that you can configure the fan to come on only when they are needed. In terms of airflow, the ML120 RGB Elite fans provide up to 58.1 CFM and improved static pressure of 2.9mm.Now plug the SATA power connectors into your PSU and turn on your system. Your fans should start working and the RGB should light up immediately. – Setting Up the Software Thanks to the fact that LL120s support PWM, they are ranged fans as they can be controlled to provide speeds from zero to 100 percent. This means that you can utilize them at zero RPM and make them run at their full capacity of 1500 RPM. These fans run at low noise even at high loads; however, the ML series are louder than the LL120s. The ML 120s can go up to 30 decibels while the LL120s max out at 24.8 decibels. Yes, the ML120s are louder but that’s because they spin faster at higher loads and can reach up to 2000RPM compared to the max 1500 RPM of the LL120s. – Setting Up

Additionally, the LL120 RGB lights form a ring on the outside of the fan while those of the Corsair ML120 RGB Elite focus on the fans.Rule 1// The tubes of the radiator must avoid the tenon of the UNI FAN and be at the safe area, which is in grey in the image. You can set them up so they don’t spin until they’re needed, which allows you to enjoy an extremely quiet setup if your case isn’t too hot. This zero RPM ability makes them a good choice as cooling fans for AIOs. In terms of airflow, the LL120s do a good job as they’re able to attain 1.61mm static pressure and a fan airflow of 43.25 CFM. What Is Corsair ML120 Best For? Once you’ve done that, take the lighting connector that’s attached to the fan and plug it into any of the ports labeled one to six on the lighting control hub. Take note of the label here as it’ll be vital to the light control. We recommend that you do it in a sequence to make it easy for you to remember. The CORSAIR LL120 RGB LED PWM fan boasts 16 independent RGB LEDs across two separate light loops to create vibrant lighting and visual effects. TWO RGB LIGHT LOOPS The fans themselves feature two cables with one connecting to the motherboard or fan control unit and the other connecting to the RGB control unit. – Performance

Since its inception, the LL120 has been a favorite among PC builders because of its low-noise performance and RGB lighting effects. The LL120 RGB fan kit comes with two RGB fans and an RGB lighting control hub that connects to your fans and powers the RGB lighting. Complete PWM Control: Dynamically control fan speed from 600 RPM to 1,500 RPM to minimize noise or maximize airflow The LL120 is the best fan for those who are looking for premium cooling performance and excellent RGB effects without sacrificing their noise levels. They come with over ten cooling effects and since their RPM is only up to 1500, they run quietly even at max load. – Features

Do not connect more than 10 UNI FANs (device up to 21W) to the controller (UNI HUB) when performing white static color. To connect more devices, please update to L-Connect 2 (reference to update guide) and use 2 or more controllers. This product is intended as an expansion of the LL120 RGB LED 3 fan kit with Lighting Node PRO. The RGB functionality of this product requires an RGB Lighting hub and Lighting Node PRO. COMPLETE PWM CONTROL The setup of the ML120s requires the same process as the LL120s. All you have to do is plug the fans into the RGB lighting control hub, the control hub to the lighting node pro, and connect all power connectors to their motherboard and PSU headers as we’ve explained above. Conclusion Next are the PWM fan connectors, which can be connected depending on your rig. You can connect them to an AIO to use your fans as cooling fans, directly to your motherboard, or connected to a fan hub.