Read the test results by comparing the color of the solution to the High Range pH Color Chart. The tube should be viewed in a well-lit area against the white area of the chart. The closest match indicates the pH of the water sample. Rinse the test tube with clean water after use. Note that when they say to wait for 5 minutes, this is the minimum time you need to allow for the color to change in the solution. In my observation, you can read the results any time after this; even up to hours later, the color holds the same. By the time I finish the last test, it has often been almost 5 minutes of wait time for the first test (Nitrate).

API® | POND MASTER TEST KIT - API Fishcare API® | POND MASTER TEST KIT - API Fishcare

One question I have is this: does it matter where you take the water sample from in your aquarium? Does anyone know if values vary significantly enough to matter in different parts of the tank? Cap the test tube and shake vigorously for 1 minute. This step is extremely important to ensure the accuracy of test results. Read the test results by comparing the color of the solution to the Ammonia Color Chart. The tube should be viewed in a well-lit area against the white area of the chart. The closest match indicates the ppm (mg/L) of ammonia in the water sample. Rinse the test tube with clean water after use. Invert that bottle: The testing seems reliant on putting in an exact amount of both water and test solution(s). API has calibrated the solution to add in drops, but the drops need to be the correct size; namely, from an inverted bottle that is straight up and down. Also take care to not touch the dropper to the edge of the test tube as this will not result in a full drop. The water tested should initially be filled to the test tube white line, preferably following the protocol of bottom of fluid meniscus at the white line. pH is the measure of acidity in your water. A pH reading of 7.0 is neutral, a pH higher than 7.0 is alkaline, and a pH lower than this level is acidic. It is important to keep your aquarium at the appropriate pH level to ensure optimal water quality for your specific fish species, as different types of fish require different pH levels for their habitats. API FRESHWATER MASTER TEST KIT will enable you to test the pH levels in your water as often as needed!If you’re looking for a reliable and affordable freshwater testing kit, you should look no further. A pdf of my instructions is located here for those who would like to print one out for their kit. Please note that the my simplified instructions do not include all the important details that are included in API’s instructions; you really do need to read their literature carefully the first few attempts. After a few tries, you will get the rhythm down and become faster at completing the test. Part of the learning curve for me getting into the aquarium hobby was familiarizing myself with water quality parameters. My first foray into fish keeping, as a child, didn’t involve much in the way of keeping healthy water. About all I understood was that tap water had chlorine and I needed to add dechlorinator when I performed a water change. The test kit comes with (4) mixing test tubes that you perform the tests in, (4) caps to cover the test tubes with (handy since the tests require mixing by shaking or inverting), (7) individual bottles of various fluids that are used individually or in pairs for testing, instructions, the results color chart, and a handy container that keeps it all together. The container also holds the test tubes upright for you while you perform the testing.

API Freshwater Master Test Kit Review - Spec-Tanks API Freshwater Master Test Kit Review - Spec-Tanks

My only previous knowledge of aquarium water testing was with test strips. These still exist and are a good option for those that want a simple test kit. It is as easy as dipping strips of test paper directly into the aquarium for a time, removing the strip to wait for a time, then comparing the colors to a provided color chart. The advantage is the simplicity. This time around, I have learned more about what is going on with the water and how the biological filter works, where bacteria in the tank breaks the fish’s ammonia waste into Nitrite; then nitrite into nitrate. This healthy bacteria is the goal of completing a fishless cycle; will talk more about this in a separate upcoming post. Add 8 drops from Ammonia Test Solution #1, holding the dropper bottle upside down in a completely vertical position to assure uniformity of drops. Large pallet items like aquariums are deemed delivered successfully with no damage once the the driver has left the property. If a report of damage is submitted after the driver has left we may be unable to assist with replacements. We recommend refusing a damaged delivery, this is the fastest resolution. API® STRESS COAT water conditioner makes tap water safe for fish by removing chlorine, chloramines and heavy metals from tap water, and contains the healing po...Moreover, you can use this container while waiting for the results to appear, as you compare them to the provided chart. API® MELAFIX fish remedy is an all-natural antibacterial treatment that works to treat infections in fish. Common bacterial infections are open wounds and abra... All Products ALGAEFIX™ STRESS COAT™ MELAFIX™ ALGAE SCRAPER FOR ACRYLIC AQUARIUMS ALGAE SCRAPER FOR GLASS AQUARIUMS ALGAE PAD FOR ACRYLIC AQUARIUMS ALGAE PAD FOR GLASS AQUARIUMS TURTLE FIX™

API® | POND MASTER TEST KIT API® | POND MASTER TEST KIT

We recommend that you take a few minutes each week to monitor your aquarium conditions and create a better underwater world for your fish. Testing your aquarium water has never been so easy or accurate! For an affordable price, this testing kit will allow you to test all the crucial parameters that affect the life of the animals and plants in your tank. The real positive of the liquid master test kit is the pricing. It is a bit tough to breakdown the number of available tests in the bottles. API advertises ‘over 800 tests’ but this is for all the separate tests combined. Each bottle has 37ml of fluid, but they each utilize different numbers of drops per test. I think the Nitrate test would run out first and I estimate that it would be good for around 80 tests. Other tests would last much longer.Performing partial water changes can also help reduce nitrate, especially if the level is very high. However, because many tap water supplies contain nitrate, it can be difficult to lower nitrate levels by this method. Comes with 6 bottles of liquid test reagent, 4 glass test tubes with snap-tight caps, a holding tray, and instruction booklet Simply run the water, open the test tube gently (do not twist the cap), and allow the water to dilute and rinse the contents out of the test tube. Avoid getting the contents of the test tube on your skin.