Cover the area with dust sheets and then pop the 8mm bit in the drill and position the tip on the drilling point and start drilling. Don’t force the drill bit into the surface too much, let the drill do the work. If it’s not possible to install an outside tap, another way to provide a water source would be to install and use a water-butt. This is a great way to capture and store water, no just because rainwater is pretty readily available in the UK, but also because it is free! The last job to do then is to use a suitable exterior sealant and pump a load of it into the sleeve and around the external hole to seal it up and prevent any draughts or water ingress. Do this on the inside also. Only you know your level of competence but if you haven’t done any plumbing before then installing an outside tap might be a bit much for you. The most common way of connecting this to the water supply is to add an elbow to the copper pipe coming from the outside tap using a 15mm brass compression elbow or Speedfit.

FixtheBog 20mm MDPE Outside Tap Kit With Plastic Wall Plate

Once you’ve made it through with the small drill swap for the large bit and then re-drill the hole from the inside. Once about half way through, go outside and drill out the rest of the hole. As said, this will prevent the large drill bit blowing a huge chunk off the face of the outside wall. Step 4 – Fit Isolation Valve and Drain Plug

Be First to Comment

You can replace the washer on the outside tap, but sometimes it’s so much easier and less of a headache to just replace the tap. As you can see, all of this has been made using copper pipe and copper compression fittings and this is absolutely fine, but if you have never attempted any plumbing before we would suggest that you use Pushfit fittings as they are much easier to work with. I turn off the hammer function on the SDS drill when I only have an inch or so to go and use it in drill-only mode.

Fittings - The Caravan Warehouse Caravan Water Fittings - The Caravan Warehouse

To insatall an outside tap correctly and ensure all works as it should do, you will need the following products and tools: As you now know the type of tap you need and all the other tools and products, it’s now time to go through exactly how to fit an outside tap. When you’ve put the pipe through the wall, take a look at your pipework on the inside and figure out how you’re going to connect your pipe. You need to make sure you’re connecting your tap to a cold water pipe. If you’re not sure which is the cold pipe, you can run the hot tap for a minute. The hot pipe will get warm and the cold one will stay cold.

Seasonal Maintenance for Outside Taps

Always start with a small drill first to drill a pilot hole as this takes the strain off the drill trying to drill too large a hole in one go and also when it busts through the wall on the other side it doesn’t blow a huge chunk off. Position the pipework up to the T-joint so the end is up to the collar and mark a point on the wall for the pipe clip to fit. Mark and drill the fixing hole and then fit the clip to the wall using a screw and wall plug. Apart from a handy supply pipe you also need to ensure there is enough free space to install the necessary pipes and work comfortably. Aside from the tap the next most important item is a water supply. When looking for a location to install your tap, it’s a good idea to select one next to or near an existing mains water supply pipe.

How to Fit an Outside Tap: Complete Step-by-Step Guide

If it freezes and expands inside a pipe it can very easily cause it to burst which can be a nightmare in terms of leaks and also having to repair it.There are no outside tap kits that use everything I like to use, but if you can make it work then go for it. My Outside Tap Kit List To make sure you have a good supply of water to your water-butt connected system it is a good idea to collect water from any available sources such as gutters and down pipes from your house and any sheds you may have. Once the guttering is fitted and water is able to fill your water butt you can use a simple tank connector, available for all plumbers merchants, to join more water butts together, giving you more storage. Measure the depth of the hole and cut a suitable length piece of 22mm copper pipe so that it is roughly 10mm shorter than the hole depth so that you have a 5mm inset at either end.

Outside Tap Kit With Plastic Wall Plate and Garden 25mm MDPE Outside Tap Kit With Plastic Wall Plate and Garden

During the colder months of the year, the chance of the temperature dropping to the point of freezing is quite high and as you probably know, when water freezes it expands. Finally, cut another length of pipe so that it runs up to the hole through the wall. It should be around 10 – 15mm short of the hole to allow for a 90° bend to be fitted. A pipe clip also needs to be fitted along this section. The easiest way to make a sleeve is by using a length of 22mm plastic or copper pipe cut to the depth of the hole and then pushed through. Once the hole is drilled you can then start fitting the pipework. Cut a short length of pipe to run from the T-joint to an isolation valve. Again, using copper or Pushfit is totally fine, but if you are new to this sort of work then Pushfit is the way to go. Fit the valve to the end of the pipe.There are some decent outside tap kits you can buy, but you should try to avoid using a flexible hose when fitting an outside tap. Ideally this will be somewhere where there is plenty of space as you will need to get a large drill in there. The first thing to do inside is cut the copper pipe from the new outside tap down to the correct length. Outside tap pipe coming through the wall You can use brass or plastic hose connectors but brass ones are better. Outside tap fitted with new hose connector