Remove the two jumpers from CN2, and place them at the two outermost empty jumper pins marked CN11 and CN12. Espressif have published some code for the TLK110. But it is relatively expensive (around 6 EUR when bought in small quantities) and is relatively big as it has an MII-interface which is not entirely needed. I also find this https://esp32.com/viewtopic.php?t=5732 but before removing the crystal I prefer to be sure I'm not missing something else. The entry: #define D_ZIGBEE_NOT_STARTED "Zigbee not started" is duplicated in i18n.h from all language files. This produces a warning while compiling due to redefinition if changing the language in my_user_config.h

While we're certainly not thinking of dropping Ethernet for future products, at this point we do not have any publicly announced upcoming chips with Ethernet in it. (I cannot comment on if the feature is in not-yet-announced chips, sorry for that.) Note that you could always add e.g. a SPI Ethernet chip to an ESP32-S3 to get Ethernet connectivity, although I agree that is not as optimal as simply having an integrated MAC. I have copy and pasted template {"NAME":"WT32-ETH01","GPIO":[1,1,1,1,1,1,0,0,1,0,1,1,3840,576,5600,0,0,0,0,5568,0,0,0,0,0,0,0,0,1,1,0,1,1,0,0,1],"FLAG":0,"BASE":1} Installing using the ZIP file and then updating using the Library Manager will result in duplicate libraries. TheLAN8720A/LAN8720Ai connect via an RMII interface.These devices support HP Auto-MDIX†, employ Microchip's proprietary flexPWR ® technology andare available in both extended commercial (0°C to 85°C) and industrial (-40°C to 85°C) temperature range options.it would be great to connect for example some relay for domotic usage and having it cable by lan instead of wifi only BLE_ESP32 (xdrv_79): Start scan as soon as we are connected to a device - saves missing a few adverts. If everything goes well you should have a UF2 file in build/examples/httpdcalled pico_rmii_ethernet_httpd.uf2. You can now load this UF2 file onto your Pico in the normal way. Add commands ``ZbNameKey``, ``ZbDeviceTopic``, ``ZbNoPrefix``, ``ZbEndpointSuffix``, ``ZbNoAutoBind``, ``ZbNameTopic`` as synonyms for ``SetOption83, 89, 100, 101, 110 and 112`` respectively

BUT when I turn wifi off (wifi 0 in console or changing wifi configuration to non existing wifi), I also loose Ethernet connection. In the future, Ethernet support using external PHYs will change significantly and support may change.

Parametrics

Go grab your Raspberry Pi Pico board and a micro USB cable. Plug the cable into your Raspberry Pi or laptop, then press and hold the BOOTSEL button on your Pico while you plug the other end of the micro USB cable into the board. Then release the button after the board is plugged in. ESD Protected MII/RMII 10/100 Ethernet Transceiver with HP Auto-MDIX Support and flexPWR짰 Technology in a Small Footprint ESD Protected MII/RMII 10/100 Ethernet Transceiver with HP Auto-MDIX Support and flexPWR Technology in a Small Footprint

A better choice seems to be the LAN8720 which costs only 1EUR and is significantly smaller as it only has a RMII-interface an therefore lesser pins. Microchip's LAN8710A/LAN8710Aiarehigh-performance, small-footprint, low-power 10BASE-T/100BASE-TX transceivers specifically designed for today's consumer electronics, industrial and enterprise applications. The LAN8710A/LAN8710Aiarethe industry's smallest footprint solution with up to 40% lower power consumption than existing Microchip transceivers. The LAN8710A/LAN8710Ai have an integrated voltage regulator and ESD protection components to help reduce Bill of Material (BOM) costs. EDIT: After reading that the lenght of wires can be an issue at 50MHz, I wired it with 10cm wires (instead of 20cm on the photo), still the same.iBeacon (xdrv_52): Clean up BLE_ESP32 based driver; add commands and advert timing. Remove HM10 code - it's in the other one..... The LAN8710A/LAN8710Ai connect to the MAC layer using a variable voltage, digital standard MII or RMII interface,These devices support HP Auto-MDIX†, employ Microchip's proprietary flexPWR ® technology andare available in both extended commercial (0°C to 85°C) and industrial (-40°C to 85°C) temperature range options.

Add commands ``ChannelRemap``, ``MultiPWM``, ``AlexaCTRange``, ``PowerOnFade``, ``PWMCT``, ``WhiteBlend``, ``VirtualCT`` as synonyms for ``SetOption37, 68, 82, 91, 92, 105 and 106`` respectively ESD Protected MII/RMII Fast-Ethernet PHY with HP Auto-MDIX and SMSC flexPWR TM in a Small Footprint I wanted to have only Ethernet connection due to my wifi problems (that was the reason I chose esp32) For using the thermostat function, publication of the measured temperature was using the wrong name. Changed to the common used name. Example configuration entry ethernet : type : LAN8720 mdc_pin : GPIO23 mdio_pin : GPIO18 clk_mode : GPIO0_IN phy_addr : 0 # Optional manual IP manual_ip : static_ip : 10.0.0.42 gateway : 10.0.0.1 subnet : 255.255.255.0 Configuration variables: ¶Rejecting a RMI support is very very bad decision. Now I m forced to search some another solutions, that allows me to stay in low price for bill electronics components and sufficient LAN network performance. the advantage could be that if wifi is not good we can use lan cable, maybe it could be PoE powering? Raspberry Pi Pico has a lot of interesting and unique features, but it doesn’t have networking. Of course this was only ever going to be a temporary inconvenience, and sure enough, over Pi Day weekend we saw both USB Ethernet and Ethernet PHY support released for Pico and RP2040. Raspberry Pi Pico and RMII Ethernet PHY When STM become officially supports external PHY Ethernet, I will delete this repository. Hardware requirements Higher frequencies come with reduced available bit depth (as by https://esphome.io/components/output/ledc.html).