Manufactured from corrosion resistant polypropylene, SEAT fans are both durable and light weight making them easy to install and a more reliable and cost-effective option for chemical laboratories than alternatives in the marketplace. With fume cupboard systems being long term investments within the education sector installers look to integrate the most efficient fans and components. Our range of EC polypropylene fume extraction fans can help designers to reduce fan energy consumption by up to 20% without affecting performance. SEAT polypropylene fans used in school fume cupboards tend to be the smaller fans in our range as schools usually service one cupboard per fan. For laboratories where there are multiple fume cupboards per fan, we can offer a larger solution to suit. All the standards that were on the EU Commission list of Harmonised Standards for ATEX were transposed and became Designated Standards for the UK legislation. Use of such a standard gives a presumption of conformity with the Directive/Statutory Instrument for those requirements covered by the standards. The Designated Standards list continues to refer to standards by their EN number, rather than their BS number. The coverage of each standard, in respect of the directive/SI requirements, is given in a specific European Annex to the standard.

Funme Hand Fan with Rechargeable 9000 Battery Fan 53 Hours

Auto Extract Systems can help specify and design the right LEV system for your business's requirements. We only use the highest quality products and installations come complete with a 12-month installation warranty. To be fitted at the lowest point of the fan scroll to allow water to run away. Thread size 3/8″ BSP, hose connection 12mm Ø. Fan housing predrilled and tapped to hose connector. means of transport for example vehicles and their trailers, intended solely for transporting passengers by air, road or rail. Vehicles intended for use in a potentially explosive environment are not excluded.In addition to our s range of plastic extract fans, we offer a wide variety of general accessories and controllers to complement the range.

Plastic Extract Fans | Axair Fans UK S Range – Plastic Extract Fans | Axair Fans UK

The required EU CE Marking is supported by ATEX documentation; UKCA marking is supported by UKEX documentation. The UKEX Certificate number and UKCA marking can be applied either additionally to the ATEX marking, or as an alternative. Most manufacturers seem to have elected to show both sets of marking at the same time. The relevant number of the Notified Body and Approved Body, responsible for supervision of manufacture, must be marked adjacent to the CE and UKCA marking. For components, where the CE and UKCA marking are not applied, both numbers should still be shown, if relevant. SEAT fume cupboard extract fans are particularly popular in educational facilities, not only because of their resistance to chemical impairment, but also due to their minimal noise emissions, simple control & monitoring, and their easy installation. One product that you can pair with a fume extraction fan is an extraction arm. Extraction arms provide a flexible solution for capturing harmful contaminants. The arm can be easily moved to capture fumes and dust at the source. Extraction arms connect to a hose that removes hazardous particles before they have a chance to reach workers. We offer fume extraction arms and laboratory extraction arms, providing businesses with plenty of choices to implement a solution that suits them the most.OEMs, Contractors, Mechanical Engineers and Specification consultants entrust Axair Fans with their industrial fan selection for a wide range of applications including air handling units, water treatment, fume extraction, commercial kitchen ventilation, biomass, fan coil units and much more. Our team of in house technical engineers are experts in their niche field, split into the OEM and Industrial division, your enquiry will be directed to the right team to correct select the fan you require. View all industrial fans using the product selection categories below or search by the main navigation menu. The weather pedestal offers a more enclosed casing for outdoor installations, it totally covers the fan motor beyond the IP55 protection.

Corrosive Fume Extraction Fans | Axair Fans UK Corrosive Fume Extraction Fans | Axair Fans UK

There is always a risk of accidents happening where there is a large variety of chemicals stored or where there are ongoing operations producing vapours and corrosive gases. Fume cupboards prevent potentially dangerous vapours being released into the classroom in two main ways; through ducting or through filtered, recirculated air. Ducted fume cupboards draw air through the sash opening over the working area and through ducting to the outside of the building, most often the roof. This method is widely used as it suitable for extracting more toxic vapours than recirculating filtered fume cupboards. The latter is more suited to experiments using much less hazardous substances. Additionally, school fume cupboards act as a physical barrier between reactions and the classroom or laboratory. This provides a degree of protection against inhalation exposure, chemical spills and fires. We can also pre-wire to electrical isolators to the motor terminal to ensure first class electrical work in factory conditions and an isolator fan on the pedestal. A fume extraction fan is most effective when used in conjunction with other types of products and accessories. Whether you require additional components to go with a fan depends on several factors, including your operational tasks, environment size and installation location. ATEX rated non-sparking versions of our corrosive extract fans are required where there is the potential for explosion. Some common examples would be: All speed controllable ATEX motors receive less cooling air on speed reduction and must therefore be supplied with thermistor over-temperature sensors to protect against shell temperature in excess of the motor temperature class. ExclusionsA variety of construction materials to suit client specification – eg. PVC, Polypropylene, GRP reinforcement Electric motors are susceptible to over-heating when running on over-load, when their supply or self-cooling air is reduced, when ambient temperature is too high or when any part of the motor surface is thermally insulated by its installed situation. Any one of these conditions could lead to an explosion.

Funme USB Desk Table Fan Updated 6 inch Desktop Small

This is an amazing service we do for thousands of businesses throughout the UK and Ireland every year. We work with such a wide variety of industries, from manufacturing, industrial, woodworking, pharmaceutical and automotive workshops to schools, colleges and military establishments. The SEAT S35 models were applied to the extract hoods over the laboratory furnaces. Supplied complete they were delivered with weather pedestals, flexible connectors, anti-vibration mounts and flanges. We also supplied an S20 fan for use with a small specto-analyser. Another product from Auto Extract that you can use with a fume extraction fan is a cabinet. Fume cabinets are ideal for situations where maximum efficiency is necessary when extracting harmful fumes. The cabinets are designed to allow operators to see through the cabinet while working, yet protecting them at all times by safely controlling exposure. The fume extract fan will collect and dispose of fumes before they become airborne. Certain environments, such as laboratories, may require fans that can withstand corrosive fumes or explosive gasses. Equipment and protective systems intended for us in potentially explosive atmospheres regulation 2016.Air flow controllers can be incorporated to monitor and control air speed and show the correct functioning of the fume cupboard’s air flow. Different versions are available depending on your requirements. All polypropylene extraction fans are directly driven by IEC dimensioned electric motors manufactured to BSN4999-EN60034 Standards and are selected on their capacity for: