EASYJoint brush-in patio grout , is a really simple, fast and DIY friendly way to fill the joints in paving slabs and flagstones. Market-leading EASYJoint is ideal for all types of paving such as natural stone, limestone, porcelain, sandstone, Yorkstone, Indian Stone, granite setts and concrete flags. Once the water drains out of it, curing will start immediately, and it should get hard in 12-24 hours afterward. Ideal for use with natural stone, limestone, porcelain, Yorkstone, Indian Stone, granite setts and concrete paving slabs

EASYJoint is the original sweep-in all-weather jointing compound and still the best truly "All Weather Paving Joint Compound". Do not be fooled by other paving jointing compounds making similar claims. Azpects sells tens of thousands of tubs of EASYJoint every month to satisfied customers all over the Europe and North America. Using small quantities of EASYJoint, simultaneously spread and wash the compound across the surface using a light jet of water and a broom/squeegee, allowing it to fall into the joints

Maintain the Width of Joint Throughout. Maintain at least a 3mm gap width throughout the depth of the paving material. Never have this type of paving butted together. See photograph. Clean out the old jointing product completely to create the correct joint size (see information under the ‘Joints’ section). Do not use EASYJoint if the correct and fully clean joint size cannot be obtained.

Continuously Wash the Paving. The hose operator should alternate between following the sweeper to aid washing the compound into the joints and moving ahead of him/her so that the paving is always wet. This is particularly important in warm/hot weather conditions. The same rules apply when working with porcelain paving tiles as with working with stone or concrete. The base on which the porcelain is laid MUST BE PERMEABLE. Yes, you can pressure wash your patio, but you should use a fan tip nozzle and stay at least 6″ away, so it doesn’t damage the pavers. No, rain won’t matter. Sand is heavier than water and when it is in the joint it will stay there unless you have a torrent of water coming off of a roof that by sheer force is pounding it out of the joint. Some concrete paving is made in moulds and has chamfered edges creating a 'V' shaped joint between two paving slabs, wider at the top than at the bottom. This gap shape can be the most challenging to work with and we recommend you carefully follow the instructions below.

Less Effort: The wash and sweep in application method makes it easy to use and jointing paving is faster than traditional methods Sponge Machines & Ancillaries We supply a range of indoor & outdoor sponge machines from Refina & Berta which are suitable for cleaning epoxy & cement grouts such as UltraScape Flowpoint from quarry tiles, external paving slabs, natural stone and granite setts. Our range of sponge machines protects the joints between paving slabs by avoiding washing away the cement, whilst the machine removes the need for individuals to wash away grout on their hands and knees. The result of using EASYJoint, to joint your paving, will be a paving gap that is completely filled that will last for years. A strong joint that will resist the elements and stand the test of time – better than traditional jointing methods

Yes, theoretically EASYJoint can be used below 3 degrees down to freezing conditions, however in these conditions, the use of lots of water becomes more difficult with a greater risk of staining. Where possible avoid using below 3 degrees, use with caution. Does EASYJoint stain paving slabs? Additionally, ensure the project has a suitable “fall” to allow surface water to drain away. Base Mix Deliveries are made between 8.00am – 5.00pm Monday – Friday although we will give you as much notice as possible for early/late deliveries. Floor Levellers & Preparation We offer a range of single & two-part flexible, reinforced and deep fill floor levellers, bulking concrete, primers and vapour suppressants for preparation of your subfloor prior to tiling or laying floor coverings. Work cleanly, clearing both the sand grains and the binding oil from the surface as you go. Keep washing until the “rainbow effect” oily water is no longer evident.

Some concrete paving is made in moulds and has chamfered edges creating a ‘V’ shaped joint between two paving slabs, wider at the top than at the bottom. This gap shape can be the most challenging to work with and we recommend you carefully follow the instructions below. The wide widths are not a problem and can be 5″ or more; however, when you have really wide joints you also need to have a little more depth, so it doesn’t break up when it is stepped on.

Similarly, while EASYJoint remains wet, either via the application process or through rainfall, the curing process will be suspended. Prolonged periods of rain, or several intermittent showers will considerably extend the setting times. Again, this will not affect the final integrity of the product in any way provided water can drain easily away and so allow even curing throughout the joints (as previously explained) Why use EASYJoint? Both the bedding and sub-base must be permeable. When using a mortar bedding mix, this should be no stronger than 6:1 (sharp sand: cement). Be careful when using add-mixtures such as SBR or PVA as these can seriously affect the permeability of a mortar mix. Suitable for Light Vehicular Use On Dense Grade Projects. (For permeable driveway installs Refer to EASYJoint Pro) Less water is needed when applying EASYJoint to porcelain paving, as there is little risk of residue staining. You will find that a small amount of water, added to form it into a slurry, will make it easier to fill the joints properly. When applying to porcelain, to ensure an effective joint, the operator MUST strike the joint off, to compact the grout fully. Compaction forces out air and water which helps the joint harden faster. Years of research and continuous development of our jointing compound makes this a market leader. We sell tens of thousands of EASYJoint tubs every month throughout the United States, UK, and in Europe.Utilise the same method when working with porcelain paving tiles as with working with stone or concrete. The base on which the porcelain is laid must be able to drain. If the base is non-permeable then EASYJoint Pro or EASYGrout should be used. Subject to the other provisions of these conditions, Building & DIY Supplies shall not be liable for any direct, indirect or consequential loss (all three of which terms include, without limitation, pure economic loss, loss of profits, loss of business, depletion of goodwill and similar loss), costs, damages, charges or expenses caused directly or indirectly by any delay in the delivery of the Goods. Zero Waste – Opened tubs of EASYJoint, if not fully used, can be kept for later use providing they are covered by a minimum of 2″ (50mm) or more of water Technically advanced: Years of research and continuous development of our jointing compound makes this a market leader. We sell tens of thousands of EASYJoint tubs every month throughout the UK and in Europe. No, the paver chatter that is developed when vehicles drive over pavers causes the EASY Joint to break down.