This is a fully compatible replacement remote control and performs all fixed functions of the original remote (excluding reprogrammable buttons) Opened case, washed rubber membrane in soapy water, dried it, reassembled and now works fine. Thanks again.... all in less than 10 minutes!! I'm a little confused here, your saying they use a 3 digit code yet the link points to a PDF file that gives 4 digit codes for example for my Sony TV, do i just miss first or last number or something.

Humax Remote Control RM-F01 - Issues | AVForums Humax Remote Control RM-F01 - Issues | AVForums

The indents are on the top plate at regular intervals. The "hooks" are on the side of the base. You just need to find the first one to spring... The PCB edge is very close to the points where the knives are inserted to open the casing, so be careful not too push them in too far as the board could be easily damaged. One man's seldom-use buttons can be another man's essential buttons. The RM-109U can not pause the HD(R) Fox T2. It also cannot pause a DTR-T1010. Bingo Barry many thanks, comes in very handy as I have 2 variants of remotes so i saved then for the future, many thx.I found that plastic Gap Openers are very good for opening these units up. These Gap Openers are small plastic blades that may be used to prise casings apart without damage, they often come free with equipment such as car dashboard mountings, or can be bought cheaply on the internet, often as part of an "Ipod Opening Toolkit". When handling the PCB be careful not to touch the board printed circuit or the on board chip with bare fingers as I would be a bit concerned that ones body static may damage the chip. I am not sure how static tolerant chips are these days; it used to be a problem some years ago, where static could destroy electronic chips. Of course if one earth’s themselves, (I do it by touching the bare steel frame of my PC that happens to have the cover off), then there is no problem.

Humax RM-F01 Foxsat-HDR Freesat Remote | Humax Direct

Press and hold the 0 and OK buttons simultaneously for 5 seconds until the PVR button on the remote stays red.The RM-109U also controls the HD(R) Fox T2 but has a few seldom-used buttons missing and only controls the HDR and TV using the MDB1.3_01 code library. Has anyone managed to open up Remote Control RM-F01 without breaking anything, there appears to be no screws available? Thank you, gave me the confidence to get it open. Cleaned board with pcb cleaner, reassembled, good as new. I used cotton buds and methylated spirit to clean the printed circuit board. Ensure the chrome ring is reset correctly at NSEW positions and that the battery springs are in the right place. Remember that everything is carried by the upper plate (the circuit board and button rubber is lightly clipped to it); including the battery springs which should lift out of their holders as you prise the cases apart.

Freesat Humax FOXSAT HD-FOX Remote Control RM-F01

Holding the remote horizontally, i/r window to the left (I'm right handed) with the side of the remote facing you, peak over the top and draw an imaginary line across the remote towards you from the top of the "OPT+" button. Your typical remote uses plastic clips molded into the body to hold the top and bottom halves together. Sometimes, you might need to push in either the top or bottom edge along the seam to help pop the clips apart.Have a problem with your product and don't know what's wrong? Fear not, we're here to help. Get in touch by: Once open, carefully remove the circuit board (mine had 2 small lugs holding it near the battery end which can be carefully prised apart) From initial setup, updating to the latest software or frequently asked questions, follow these links to help you get sorted with your product: Lets you turn on display of recording crid codes in programme info. Handy when the box comes up with odd recording clashes.

Humax RM-F01 Remote Control for Foxsat HDR Freesat Box,Black

Worked for me too although I couldn't actually see any dirt. I wiped the circuit board with a small amount of carbon tet as I didn't have any alcohol to hand. I followed Philip Bradbury's method and it worked perfectly, without any lugs broken. It took me about 1/4hour in all to do - don't be scared to try it - you shouldn't to force it off. Thanks for taking the time to look. Unfortunately the source button doesn't do anything from the RM-F01, when used with the code 108 but it does light up the audio button, so a signal is being sent. The other two codes do nothing from the sources button.I've opened and cleaned my one many times but as most of the wee retaining clips have long since snapped off, I've decided to replace it. So it's not the remote. Thanks just tried it again - yes my HD remote does use the 4 digit codes - you have to press OK after each code to then test it - it doesn't send a power off after entering the 4 digits as stated in the manual which makes it slower to find the correct code. Start in the middle and work carefully upwards and downwards.