The XG 16 has twelve 10 Gbps SFP+ slots and four 10 Gbps RJ45 Ethernet. The 2nd generation Aggregation, XG, or Enterprise models may be better options. We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti. For more details, visit: ui.com/toughcable I have been at this for hours and changed almost every configuration I could think of to get it to work and still nothing. I am running a Netgear c7000v2 with Internal IP of 192.168.0.1 going into a Zimaboard with PFSense 2.7.0 with DHCP from Modem of 192... Optional: The config can also be exported if preferred. The following example exports the output to the config.txt: To remove a certain advanced configuration, just delete the section pertinent to that configuration in the config.gateway.json. To completely remove all advanced configurations created in the config.gateway.json, delete the file or rename it. This will void all manual changes. The USG will be provisioned with the current config contained within the UniFi Network application.

RJ45 serial console port for Command Line Interface (CLI) management. Use an RJ45-to-DB9 serial console cable, also known as a rollover cable, to connect the Console port to your computer. Then configure the following settings as needed: Find the appropriate section with the custom changes in the config output, for our example above it would be the following: Redesigned to be more intuitive and easier to navigate, the new UI raises the bar for enterprise network management efficiency. Important network details are logically organized for a simplified, yet powerful, interface. With the USG Pro 4, our WAN throughput with both IPS and DPI enabled is 479 Mbps up and 647 Mbps down, as reflected on the USG Pro 4’s new speed test. Recommended Configuration

TABLE OF CONTENTS

RJ45 ports support 10/100/1000 Ethernet connections. A WAN port is active only if the corresponding SFP port is empty. By default, the WAN1 port is set to DHCP Client. The USG-PRO-4 WAN port, as a result of being a combination SFP/GigE port, is a pure 1 Gbps port – it is incapable of both 10 Mbps and 100 Mbps FDX/HDX settings. The pro models have lots of PoE, support redundant power via the USP-RPS, and have some limited L2+/L3 features like static routing and a DHCP server

Because hardware acceleration is disabled, Ubiquiti says that enabling IPS will affect the USG’s maximum throughput: This underlying OS difference causes some other differences. The UDM and UXG lines do not support editing the config.gateway.json file. By editing the configuration file manually, you were able to access features that Ubiquiti doesn’t put in the controller GUI. It also let you access hidden settings, and tweak features to work how you want. Normally, behind the scenes, the UniFi controller edits your configuration files for you. That only works with the features that Ubiquiti officially supports. If you’ve ever had to deploy a UniFi network, you know there are a many features not in the GUI. Unfortunately there is nothing like this going forward, and you are limited to what Ubiquiti shows in the controller.All of the Dream Machines and UniFi OS Consoles are based on modern ARM processors and Ubiquiti's new UniFi OS software platform. You can’t create custom JSON config files for them, but a limited set of manual configuration changes and Linux commands can be run via SSH, if you know what you’re doing. None of these can be adopted to an external UniFi Network controller besides the UXG-Pro. I remember something similar a while ago when trying to adopt a USG into an existing network using a statically assigned IP raspberry pi as controller.. I changed subnets around and tried to mess with it a bunch of different ways. It DID NOT want to be adopted. Only time will tell how the development goes for the UXG-Pro. If you have an existing UniFi network with your own controller, this is probably going to be a better fit that the UDM or UDM-Pro. The unannounced base UXG should be a good little router, if Ubiquiti can get the software right.

Ubiquiti still sells almost all of the 1st generation models of UniFi switches. They are older, but they can be better options for some networks. Unlike with the USG/USG-Pro, the 1st generation switches come without major performance limitations. Older Desktop/Small Switches

Summary - Ubiquiti USG-PRO-4 for companies betting on centrally managed UniFi solutions

NOTE: When editing this customjson file, it is not necessary to include everything. You must only include the complete "path" to the items you have edited, anything outside of the path can be omitted. EdgeRouters have been around a long time, and are still technically supported with hotfixes and occasional software updates. The newer UISP hardware line is the safer bet for long term support, although EdgeRouters still have a lot of feature advantages. SFP ports are hot-swappable and support 10/100/1000 fiber SFP modules. If an SFP module is plugged in, then the SFP port is active, and the corresponding WAN port is deactivated. By default, the SFP1 port is set to DHCP Client. For outdoor applications, shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the power supply. we replaced five legacy passive switches in our network with six 8 POE-60W actively managed switches, and

Most 1st generation PoE switches have more PoE budget than the equivalent 2nd generation model. They are still a good buy if you need a lot of PoE. Their fans can get loud though. Hardware offloading lets you use dedicated hardware to accelerate some tasks. You can turn it on or off depending on what you are trying to do. This applies to the USG/USG-Pro, and also EdgeRouters. So, many people have asked what is the benefit of using a UXG-Pro, we’ll be covering that in a separate ‘vs’ article, but in this one we are comparing the brand new UXG-Pro and the previous USG-Pro-4. One potential problem with the UXG-Pro is the current state of the UDM-Pro and UniFi OS. Some features on the UDM-Pro are not working, incomplete, buggy, or just missing. Development for the Dream Machines has been steady, but after 9 months, the UXG is still on on beta firmware version 0.5.0. Resets to factory defaults. The UniFi Gateway should be running after bootup is complete. Press and hold the Reset button for about 10 seconds until the right LED on the WAN2 port starts flashing and then becomes solidly lit. After a few seconds, the LED will turn off, and the UniFi Gateway will automatically reboot.We are very excited to announceUniFi OS- a shared platform for all UniFi Controllers. Key features: We require this information to understand your needs and provide you with a better service, and in particular for the following reasons: Basically a UDM with an upgrade to Wi-Fi 6 on 5 GHz, two PoE ports, an SD card slot, UniFi Protect support, and 128 GB of internal storage