The leading brush cleaners such as Polycell Brush Cleaner do a better job of cleaning and conditioning than white spirit, removing any chance of a colour transfer when you next... We recommend you use a plastic cup or any vessel and add 2 cups of powder (level full) to 1 cup of water and mix to a smooth paste. The...

This is caused by painting over contaminated surfaces such as wax, oil or polish. The paint cannot adhere to the surface and draws away leaving unpainted areas. This can also be caused by contamination on the brush. Putting it right I ended up with a really good smooth wall using a 500w halogen light for seeing all the imperfections but I did find though that although I had covered all the digs/dents when it came to painting I had pin holes that I thought would fill with paint but didn’t (tried Polycell base coat & Polycell flexible ceiling paint but they didn’t really make much difference) Using the wrong type of roller can cause foaming of a paint film. Sponge or foam rollers should be avoided with water-based paints. Long pile rollers must be wetted out properly. Foaming happens when air gets into the wet paint film to create air bubbles. When these bubbles burst craters are left on the film surface. Sometimes these craters dry to give an even film. Putting it right Due to time & dust issues (2 kids to think about) I will probably go to a plasterer for the rest downstairs but it has been an interesting project (apart from the peeling paint bit) The filler is versatile and can be used on any surface with the correct preparation to ensure a long-lasting, professional finish. Yes, you can use polyfills to cover large holes.Paint flaking can occur with a number of different factors. Most commonly, improper application to the wall and too much hard grain is used.

The first job is to sand them with a coarse grade of sandpaper to get off the worst of the lumps and bumps, followed by a medium grade sandpaper. Next,... Overall, the drying time for Polyfilla depends on various factors such as temperature and humidity. It generally takes 30 minutes to an hour for Polyfilla to dry in normal conditions. The Polyfilla must be kept from direct sunlight in a cool and dry place with temperatures under 70°F (21°C). To further help maintain the product’s lifespan, make sure that the lid is properly sealed after each use Hope you get on well but if its a near full skim you need then I don't think Smoothover is the most cost/time effective way, small patches yes, full skim no. (that probably goes for easyfill/skim etc unless you have all the right gear & can use it well) For ways to avoid everything mentioned above, ensure a high-quality paint is used and that the surface of the wall is primed and carefully smoothed out on a dry surface.

Use a setting accelerator: Some Polyfilla products have a setting accelerator that you can mix with the filler to make it dry faster. Depressions or surface blemishes in the paint film. A common cause is rain that has fallen on the surface before the film has had chance to fully dry. Putting it right

Allow the surface to dry and then rub down using 'wet and dry' abrasive paper and a solution of warm water and detergent. Once rinsed and dried the area can be repainted. Adding a second coat of paint will get rid of streaks left by rollers. You can make the job more seamless by taking a brush and going over the streaky areas to smooth out. Another alternative, the areas showing raised roller marks is to start again by sanding down after the paint is completely dry. Then once dry, wipe down the areas where you sanded and add another layer of fresh paint. Although obvious, flaky pieces of paint on the floor in your home is a sign. This is caused by paint failure and when the paint curls up and shatters, collapsing onto the floor. Mixing Polyfilla powder is relatively easy, requiring minimal tools and materials. To begin, you will need to gather the following:

Substance

To prevent Polyfilla from showing in paint, use a sealant to encapsulate it before finishing with the topcoat. Other precautions include sanding down any raised areas after drying and using a primer before applying the final coat of paint. The shelf life of an opened can of Polyfilla depends on several factors, such as storage conditions, type of Polyfilla, and any contaminants. Once opened, a container of Polyfilla can last up to three years if stored in the right environment. When using filler it is always good practice to thin down the first coat of emulsion when painting the surface. If this is not done, what tends to happen is... This is caused usually by a wearing away of the paint film by weathering or could be evidence of salts coming out of the surface. Putting it right

Now prime the filler and surrounding edges with a good quality prime sealer. Priming the surface will give your wall a chance to blend in perfectly when you apply fresh paint.

Frequently asked questions

Unlike plaster, Polyfilla doesn’t shrink as it dries and can be easily sanded down for smooth finishes. In addition, Polyfilla is more durable than plaster when exposed to water or high humidity levels. My house is nearly 70 years old & I initially went down the smoothover route as I had the whole house to do and the walls were in very good condition apart from a few digs & scrapes as it was a well kept one owner house with only one layer of wall paper & the original ceiling paint underneath. in 1 mould killer is designed to kill the existing mould and spores that will create new growth. Some moulds stain the area they grow on. 3 in 1...