This unit is also excellent with most LED indicators. Unlike the original incandescent bulbs, LED lamps are polarity sensitive so you may need to try swapping the connections to each indicator to get the indicators to work okay. So, to slow your flashing down you have to make the wattage draw similar to how it was with the original indicators, and you can do this by fitting either a new indicator relay unit or with resistors.

LED Flasher Unit Relay MKII - Just Add Lightness

By adding resistors to the wiring you increase the wattage draw from the LED indicators to match what was there before, therefore your existing relay will continue to run as normal with a standard flash rate. When it comes to upgrading your current indicators to an LED set, simply plugging in the new units isn't quite enough (although fitting them properly doesn’t require you to be a neuroscientist).Resistors get hot during operation, so wrapping them in tape can lead to resistor over heating or worse melting plastic parts around it. Looking to improve your flasher relay performance or are you considering or have you added LED indicator bulbs? IF THE RELAY DOES NOT BEHAVE WHEN THE ENGINE IS RUNNING YOU NEED TO ADD SUPPRESSION TO THE LEAD BETWEEN YOUR COIL AND DISTRIBUTOR TO REDUCE THE RF INTERFERENCE.

Pin Adjustable LED Indicator Relay Car Turn Signal CF13 3 Pin Adjustable LED Indicator Relay Car Turn Signal

Suitable replacement for 3 pin flasher relays with 49 (X), 49a (L) and P Connectors. You will need to also connect the earth connection wire. Also available with Positive Earth, please select the required option from the drop down menu. My car is 2008 so definitely needed this upgrade for the flashers to work correctly, two minute job to fit. Just the job. Fixes the epilepsy inducing standard LED timing with a nice calm indicator pattern. I don’t have to feel embarrassed when using the indicator any more. This applies to EU and other bikes with hazards and 4 pin relays, type Mitsuba FR33-025 (however, if you show me the insides of a 2 pin I can advise as well) Once you know you have the relay it's as simple as wiring your new motorcycle indicators in and plugging in your new relay!Getting the right LED relay for your motorcycle in most cases just means pulling out your existing relay and buying an LED specific relay that matches the pin lay-out of your current relay. LED lighting draws much less power (load) and lasts way longer than standard incandescent lighting. Replacement of indicator bulbs with LED’s will cause the indicators to flash too fast. This happens because your new LED lights draw such little power. Installing an LED flasher relay specifically designed for LED lights is the easiest method to solve this problem. What about load resistors?

LED Flasher Unit Conversion | Blog | Pedparts UK Piaggio LED Flasher Unit Conversion | Blog | Pedparts UK

Works flawlessly with all my LED signal light upgrades. Original flasher unit would not cut the mustard and so the LED would not flash or sometimes just stay on.One of the problems with this is you have to get the resistor value just right. If you fit just rear LED lights and get them flashing correctly you may need to change the resistors for different value ones if you then late additionally upgrade the front indicators.

Indicator/Flasher Relay 3 pin (Original and LED Indicators)

PLEASE NOTE: We have seen many fake LED relays on the market. They look the same but have different components inside and the casing is made from an inferior plastic. We have even tested some where the positive and negative terminals were incorrectly labelled. Please ensure you have a suitable LED relay fitted to your Caterham when upgrading to any type of LED light. Browse our range of Motorcycle Screens, Levers, Crash Protectors and Bodywork accessories. Double-Bubble screen replacements from Airblade, with three different smoked options-What more could you want?Suitable for many classic or modern cars, motorcycles or applications with standard filament / incandescent bulbs or LEDs or a mix of filament / incandescent bulbs and LED. There are many flasher relays available that look the same as this one, and are described as ‘led compatible’ which will not work unless the current draw is around 0.5A. This is less than the 3.5A that a pair of 21W bulbs requires, but still way more than many led equivalents. This relay works with a current of 0.02A so it will still flash even with the tiniest of connected loads, including any led combination.