Aluminum Alloy Doweling Jig：Be made of 6061 aluminum alloy,anodizing surface treatment,laser engraving scale in- 1 multi-function drill guide , for drilling dowel holes and vertical holes. Adjustable metal bushings accurate alignment when drilling hole, easy to adjusting drilling height and hole depth. Good thought! Also makes me wonder about door handles hitting the wall, I imagine the doors have to open completely for the drawers to come out on the left side. I'm pretty pleased with the way this worked. It took a bit to drill all the holes but it provides a nice clean joint that's secure and easy to take apart for storage or moving. Never used a jig apart from lining up the hole in the end of the board and that was a simple piece of wood with two dowels and a hole the same size as the drill bit.

Levoite™ Classic Doweling Jig Kit System Cam Lock Jig Minifix

Apart from very experienced cabinet makers nobody will get that fine a tolerance when but joining materials The storage cabinet doesn't have flush top or bottom. So I'm over-thinking this - thanks, all, for making me reconsider both the design, and my unrealistic expectations about achievable precision. Finally I drilled the hole in the side for the cam nut. Here I used the 5/8" Forstner bit. This hole is the most critical of the three. The center positioning needs to be pretty precise for the cam to engage properly. Its center is the same as the one on the edge and it's 1-5/16" from the edge. This puts the edge of the hole right underneath the top of the post. If it's too far from the edge, the cam won't engage and if it's too close to the edge the cam won't tighten against the wood. I'm working on adjusting my jigs to improve the fit, but this is WAY too hard. The fixings are good and well made, and not expensive, but in spite of years of experience making jigs of all kinds for woodworking, I'm finding these very hard to get right. For this project, three bits are needed: 3/16" and 5/16" in a twist or brad pointed bit and a 5/8" Forstner bit.Wide application: Easy to use, suitable for woodworking drilling holes and positioning. High accurate scale, easy to adjusting drilling height and hole depth. Within self tighten clamp, convenient to fixing drill guide on the wood. Become an UNLIMITED member and get it all: searchable online archive of every issue, how-to videos, Complete Illustrated Guide to Woodworking digital series, print magazine, e-newsletter, and more. Made of aluminum alloy 6061, practical, easy to operate and use, wide application range, has a long service life. Make strong hidden joints, fast and easily produced. Perfect joints, no need to pre-drill mating workpiece.Multi-ourpose drill guide , for drilling dowel holes and vertical holes.Dowelling Jig for Furniture Fast Connecting Cam Fitting Drilling Locator. Next I drilled the holes in the end piece using the 5/16" bit. The holes need to be a bit over 1" deep. Again the depth isn't critical as long as it's long enough to go into the area where the third hole will be drilled.

Woodpeckers Universal Cross Dowel Jig Woodpeckers Universal Cross Dowel Jig

Before putting the posts into the hole, I transferred a mark to the other piece. It is fairly critical to get these holes correctly aligned as the post has to go into both of them. I didn't have any dowel centers small enough so I found a self-tapping screw in the surplus screw box with an outside thread diameter the same as my hole size. I cut it to a little over 1/2" long and set it in the hole, pointy side up. I used it to mark the center of the matching hole in the other wood. Then the post could be screwed in. I can probably slightly modify the bookcase design so it isn't so critical to get flush joints, but allow (as I see IKEA do on their bookcases) the sides to project beyond top and bottom by perhaps 2-3mm. That would mask any remaining inaccuracy in the joints.Wide application- Easy to use, suitable for woodworking drilling holes and positioning. High accurate scale, easy to adjusting drilling height and hole depth. Within self tighten clamp, convenient to fixing drill guide on the wood. The home center had two types of posts: one had wood screw threads and the other had machine screw threads. I used the ones designed for wood. Both thread types came in only one size and it seemed about the same as all the other's I've seen in furniture kits. I don't know if the connectors come in different sizes or if there's pretty much only one standard. In any case, the bags for the ones I had were marked with "M6 x 45.5" for the connector bolts and "15mm x 16mm" for the cam connector. The details I present here are for these sizes.

cam lock holes? - IKEA Hackers Hackers Help: How to remake cam lock holes? - IKEA Hackers

All my bits are in imperial measurements, but the tolerances are close enough they worked just fine in spite of the metric hardware. I used a drill press for all my holes to help ensure straight holes and a good fit. If you don't use a drill press, do your best to get the holes as straight as possible. The universal dowel jig set is suitable for making edge-to-edge, edge-to-surface and edge-to-corner jointsin- 1 multi-function drill guide for drilling dowel holes and vertical holes.Dowel drill guide tools for the fixation and centering while drilling and woodworking. Adjustable metal bushings accurate alignment when drilling hole, easy to adjusting drilling height and hole depth. The hole for the cross dowel can be stopped, hiding the cross dowel on the outside of the project, or drill a hole all the way through and use the cross dowel as an accent. We manufacture a line of bright-finished stainless steel cross dowels to add some style to your project. As you can tell, the design possibilities are limited only by your imagination. I'd recommend getting two pieces of scrap material to practice on. Once you've done it a time or two, it's easier to proceed with confidence on the main project pieces. Use the 3/16" bit to drill holes for the posts to screw into. The depth isn't terribly important as long as it's deep enough for the post to screw in securely up to the shoulder of the thread. I found 7/16" deep worked well.