RJ-45 自動感測 10/100/1000 連接埠 (IEEE 802.3 Type 10BASE-T、IEEE 802.3u Type 100BASE-TX、IEEE 802.3ab Type 1000BASE-T)；雙工：10BASE-T/100BASE-TX：半雙工或全雙工；1000BASE-T：僅全雙工 Only supported for use in the SFP⁠+ ports on R0X43A module. 100FX is not supported for use in the R0X44A SFP28 or SFP56 ports of any other 6400 module. For J8692A, J8693A: K.12.01 (for J9054B/C 1990-3613); K.15.08.0007 (for J9054C 1990-4112 and 1990-4483, and J9054D 1990-4483 and 1990-4360) dual-personality ports; each port can be used as either an RJ-45 10/100/1000 port (IEEE 802.3 Type 10Base-T; IEEE 802.3u Type 100Base-Tx; IEEE 802.3ab 1000Base-T Gigabit Ethernet) or as a SFP slot (for use with SFP transceivers) ports

It prioritises traffic by specifying a port and priority level. VLAN-based prioritises traffic by specifying a VLAN and priority level. Not supported for use in the following 3800 models: J9573A, J9574A, J9575A, and J9576A. The SFP⁠+ ports do not support 100M operation. JL253A, JL254A, JL255A, JL256A, JL258A, JL263A, JL264A, JL259A, JL260A, JL261A, JL262A, JL557A, JL558A, JL559A It sets per-port ingress enforced maximums for all ingressed traffic or for broadcast, multicast, or unknown destination traffic. J8177C/J8177D are not supported for use in the Dual-Personality ports of the 2930M Series Switches.

It provides advanced configuration and diagnostics through a robust CLI. Simple Network Management Protocol (SNMPv1/v2c/v3) allows a switch to be managed with a variety of third-party network management applications. For J9310A, J9311A: K.14.50 (for J9054B/C 1990-3613); K.15.08.0007 (for J9054C 1990-4112 and 1990-4483, and J9054D) RJ-45 自動感測 10/100 連接埠 (IEEE 802.3 Type 10BASE-T、IEEE 802.3u Type 100BASE-TX)；媒體類型：Auto-MDIX；雙工：半雙工或全雙工 For J8705A and J8706A modules: K.12.01 (for J9054B/C 1990-3613); K.15.08.0007 (for J9054C 1990-4112 and 1990-4483) J9054D: K.15.08.0007

It allows real-time traffic classification with support for eight priority levels mapped to either the queues, it uses weighted deficit round robin (WDRR) or strict priority (SP). speed is NOT supported for the J8177D when used in any port (SFP+, SFP28, or SFP56) on teh 6400 series.J8177C/J8177D is not supported for use in the Dual-Personality ports of the 2920 Series Switches. For use ONLY in the J9731A module.

It forwards IPv6 multicast traffic to the appropriate interface; prevents IPv6 multicast traffic from flooding the network. For use in the SFP ports of the 2530 Series Switches. (The J9853A, J9854A, J9855A, and J9856A models have 1G/10G SFP⁠+ ports that do not support these 100Mbps transceiver modules.) RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full onlyRJ-45 autosensing 10/100 PoE+ ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3at PoE+); Media Type: Auto-MDIX; Duplex: half or full JL253A, JL254A, JL255A, JL256A, JL258A, JL259A, JL260A, JL261A, JL262A, JL263A, JL264A, JL557A, JL558A, JL559A The 2930F Switch Series models with 1G/10G SFP⁠+ ports added support for this J9054C/J9054D 100FX transceiver. The J9054C/J9054D are supported in models with 1G SFP ports.

Table 57: Compatibility for SFP copper transceiver modules. The specifications for Revision D transceiver products are the same as the specified Revision A, B, and C SKUs.The 2530-48G-PoE+ Switches are IEEE 802.3af- and IEEE 802.3at-compliant with up to 30 W per port, making them suitable for voice, video, or wireless deployments with PoE+.