David: It’s completely safe. You can put your hands in it and even get it in your eyes, it won’t hurt you. All of our other products are non-toxic as well. Evapo-Rust is an amazing rust remover, but it’s also a part of an entire range of high-quality products. I had the honor of testing a few myself and the results were positive across the board. Evapo-Rust Gel After enough time has passed, take the metal item out of the plastic container. You should be able to see two distinct changes: Also some buyers say that there aren't any positive sides in the product. I can't agree with it and I suppose these buyers have never used the Evapo-Rust. I also know that some small efficient companies buy tons of the product to use it in the production process. It can be effective in spheres of any production. Actually, this fact gives us more than warranty for optimal product quality. As I stated earlier, the beauty of this rust remover is that you can reuse it. However, you need to do it properly. Keeping it in a separate container is one option, but there is another effective alternative.

EVAPO-RUST® is an amazing RUST REMOVER which is utilized by the U.S. Army, U.S. Navy, U.S. Air Force, FBI, NATO, Government Contractors, Engine Builders, Auto Enthusiasts, Gunsmiths, Forensic Labs, OEM’s, Farmers, Antique Restorers and more. This really isn't cost effective to be used on large parts, but for small items it works quite well. Leave the item to soak for a few hours, then under running water scrub the rust off with a wire brush. The surface will be left with a matte grey finish that's very easily polished with scotchbrite. it's fully earth-friendly and doesn't cause any harm to nature, groundwater, living organisms or whatever; A lot of car bodies are really well rusting. You won't drive three days and will again see the rust coming out from paint edges. So I recommend you to paint the spot as soon as you get rid of rust. It will ensure optimal work of body for many years. For large spots it would be better to remove paint layer from the whole part and then use Evapo to remove rust. After that you can use prime coating and then usual car paint. David: We make a lot of products and we’re constantly working on more. We have products that prevent rust from even occurring. We make a version of Evapo-Rust that’s really cool, it’s called Thermocure. If your car is running hot, you just put Thermocure and water in the cooling system and drive around with it. After a few days, you drain the product, and all of the rust comes out, which is the cause of the issue. Then your car starts running cool.Before I do any submerging, I place the rusted piece inside of a container and mark the highest point it reaches; I leave the mark outside of the plastic container to avoid contaminating Evapo-Rust with the marker dye. I then pour the product, but I make sure that it’s a few inches below the marked point. Thanks to the Archimedes’ principle, the liquid will rise well above that point when I put the iron in. Step 2: Submerging the Item absolutely easy usage of rust remover, you don't need any special instruments, skills or special conditions. years ago, David Harris created Evapo-Rust, a chemical solution that easily removes rust. Evapo-Rust is non-toxic, non-corrosive, and contains no acids, bases or petroleum solvents. Most people would discard used rust remover, and doing that with Evapo-Rust is easy; it’s biodegradable and non-toxic, so you won’t be harming the environment. However, don’t throw away the used Evapo-Rust. It can be reusable, so I advise keeping it in a separate container (more on that later). Step 5: Clean the Item I mentioned I use a homemade "Evapo-Rust" type cleaner for rust removal and was asked to explain, so I figured a new topic would be useful for searching in the future.

Items that are obviously damaged should be returned to base for inspection, report and rectification. Evapo-Rust™ will de-rust without dismantling. Safe on copper, brass, aluminium, plastic, rubber, vinyl, solder points and lead. Even more amazing, Evapo-Rust™ will not remove non-oxide coatings, such as paint or chrome that are still bonded to the surface.

Cleaning the metal item involves rinsing. However, interestingly enough, you can go about it in two different ways. Rinsing with Water