The 2930F Switch Series models with 1G/10G SFP⁠+ ports added support for this J9054C/J9054D 100FX transceiver. The J9054C/J9054D are supported in models with 1G SFP ports.

JL253A, JL254A, JL255A, JL256A, JL258A, JL259A, JL260A, JL261A, JL262A, JL263A, JL264A, JL557A, JL558A, JL559A The 8325 requires configuration of "interface groups" (groups of 12 ports) to enable use of 1G or 10G transceivers or DACs in the SFP28 ports (default is to use 25G transceivers / DACs). See the

For use in the JL075A SFP⁠+ ports or used in an installed JL083A Aruba 3810M/2930M 4SFP⁠+ MACsec Module. Only supported for use in SFP⁠+ ports on JL658A. 100-FX is not supported for use in any SFP56 ports on other models.

At Intelligent Servers, we supply refurbished HP Aruba 2920 switches with a three year warranty included as standard and free remote support for the duration. All our products are also offered with free delivery worldwide. For use in the SFP ports on the models listed, and in an installed J9312A 10GbE 2-port SFP⁠+/2-port CX4 yl Model These switches only allow original SFP+ modules, unless you use the allow unsupported transceivers which voids warranty. JL687A 32p 25G module requires configuration of "interface groups" (groups of 4 ports) to enable use of 1G or 10G transceivers or DACs in the SFP28 ports (default is to use 25G transceivers / DACs). See the Table 45: (ArubaOS-Switch) Compatibility for the SFP⁠+ DACs (and specifics for HPE Server cables) Product nameFor use in the JL075A SFP⁠+ ports. Also used in an installed JL083A Aruba 3810M/2930M 4SFP⁠+ MACsec Module. The output of show modules just shows the module with two SFP+ slots, which seem not to have any (supported) SFP+ modules plugged in. That may be why the menu does not show any ports. JL253A, JL254A, JL255A, JL256A, JL258A, JL263A, JL264A, JL259A, JL260A, JL261A, JL262A, JL557A, JL558A, JL559A For use in the SFP ports of the J9263A 6600-24G Switch, the J9264A 6600-24G-4XG Switch, and the J9451A 6600-48G Switch

ER (J9153A/D) transceivers are limited to a maximum of two transceivers per J9309A or J9538A modules when used in a 5400zl or 8200zl chassis. Only supported for use in the SFP⁠+ ports on R0X43A module. 100FX is not supported for use in the R0X44A SFP28 or SFP56 ports of any other 6400 module. For J8705A and J8706A modules: K.12.01 (for J9054B/C 1990-3613); K.15.08.0007 (for J9054C 1990-4112 and 1990-4483) J9054D: K.15.08.0007 For use in the SFP ports of the 2530 Series Switches. (The J9853A, J9854A, J9855A, and J9856A models have 1G/10G SFP⁠+ ports that do not support these 100Mbps transceiver modules.) J9772A, J9773A, J9774A, J9775A, J9776A, J9777A, J9778A, J9779A, J9780A, J9781A, J9782A, J9783A, J9853A, J9854A, J9855A, J9856AWondering if someone can help please. I've had a 2920 switch for a while but only just getting round to connecting 10GbE to our main Mellanox switch. Strange behaviour with the module showing in the CLI commands but not via the menu, see below. Any attempts to plug in copper cables or fibre modules all result in flashing amber light on either port and the port doesn't go 'up'. The JL687A module requires configuration of "interface groups" (groups of 4 ports) to enable the use of 1G or 10G transceivers / DACs in the SFP28 ports (default is to use 25G transceivers / DACs). For J9263A, J9264A: K.14.03 (for J9054B/C 1990-3613); K.15.08.0007 (for J9054C 1990-4112 and 1990-4483)