thinking more clearly.... there are three elements inside the PCM as I said, 1) Engine Map, 2) Immobiliser info 3) the disabled cruise control software. You will also find that the version I have works on everything from Windows 95 all the way through to Windows 10. And yes I have had my fair share of fake units to test out and some only work on Windows XP (due to driver compatibility). The FoCCCus software is originally developed for the Focus MK3. The original developer of the FoCCCus software stopped developing the software any further about 3 Years ago.

Why on earth half of this stuff is not turned on by default is beyond me. Ford put it there and left it switched off. My titanium has stuff turned off that are turned on , on other models. how crazy is that. at this point Forscan showed a scrolling list of the modules it had found (after prompting me to toggle the toggle switch between MS & HS positions to complete the listing)

Conclusion

Solder pin 6 (which you just de-soldered) to the middle pin on your switch (middle bottom in diagram) Elmconfig is a program written by a guy on a Ford Focus forum (civil-zz) that uses the widely available ELM OBD reader/controller interface. Not only is this a useful DTC code reading tool but also a handy programming tool to modify various options and to enable features on Ford cars. Please do not attempt any mods unless you are comfortable to do so. Do any mods at your own risk. EDIT* NOTE PuTTy is not needed for ELMconfig Program , once Elm327 is connected then select configure from the menu on startup of ELMconfig , this will send all commands to re-configure your ELM327. Install USB drivers for your ELM327 ( you may have to search for WIN 7 drivers) but it does work on Windows 7 If i mess up my ECU (for which i have not seen one single post that this has happened) then it will be my fault.

Having connected the ELM327 module to the PC USB port and car OBD port and launched Forscan, I switched the ignition on when prompted – on my keyless start model this meant pressing the power button without pressing the clutch The FoCCCus software is no longer developed any further. There will never be full support for the MK3.5. After the MK3.5 was introduced the FoCCCus software turned out to be not fully functional on the MK3.5. This is because of the different hardware and software version numbers of the MK3.5. At that time the original developer of the program did not plan to modify the program to work with the MK3.5. FORScan Lite for Android - attention: some functions are missing in FORScan Lite. Please see comparison of applicationsEnsure there is NO yellow exlamation marks (that looks like this ) next to devices such as: USB-Serial CH340 | FT232R USB UART Prolific | USB-to-Serial | USB Serial Port | USB2.0-Serial | Silicon Labs CP210x USB to UART Bridge could you please help me with some AS Built data (if you have) for a Ford Focus MK2 2.0 petrol 107 kW model? C) the tool has been through umpteen revisons and some don't allow you to complete these steps with one version of the tool

Actually the FW for the 140 & 163 is the same and just a couple of bits tell the ECU that is has to use the maps for the 140 resp 163 engine. The GEM Tab or (BCM) , This will not connect , and i'm Guessing that it needs the Wiring MOD before it can connect to the High CAN BUS. Turn on the car ignition but don’t start the engine! At this point, you can launch the ELM327 software. It will automatically detect the OBD2 reader and the vehicle ECU.

This update will show the radio or CD information in the instrument cluster display. This will only work on vehicles with the large displays. For example it will work on the display shown in this sections header image. No, definitely not doing this with the engine running, but absolutely everything optional is turned off. I'm also not willing to proceed with writing until my reading times match what other people tend to experience. you need to first cut 6 wires about 3 amp will do approx 6 inches long , different colours would be better , if not then mark them individually (14 , 11 , 6 , 3 , Hcan , and Mcan. Don’t get me wrong about Torque Lite. The free version of Torque is good enough for basic applications but it had trouble reading the trouble codes on some Nissan and Subaru vehicles. These are the modules available to you in ELMConfig, most of them are pretty self explanatory. Not all modules will be fitted to all cars, for example, only the Kuga will have the AWD module. If your car doesn’t have a module, it doesn’t mean that it can’t be fitted and the functionality added to your car. There have been success stories of people adding cruise control to cars, and enabling it using ELMConfig. MS-CAN GEM