Important - If you have a brace between the seatstays - you must attach at least one cable tie to it if you don't have a brace between the seatstays - you must use 3 cable ties on each arm You should be able to locate the mudguard and let go as the rubber side pads should hold it in place (ensure the slots are centrally aligned to the threaded holes on your fork) long 24g (without cable ties) MAIN DISTRIBUTORS UK EXTRA UK FRANCE TRIBE SPORT GROUP NORWAY DELER AS REST OF EU NOW COMPANY USA AND CANADA RECIPROCATORS This mudguard design is perfectly suited for the rigours of modern mountain biking. It ensures superb all-weather protection for anything from Enduro and Downhill racing, to weekend Trail sessions with friends. And, since it’s made from RapidRacerProducts’s unique polypropylene, it gives a superbly flexible and ultra-durable performance at a low weight.

cable ties are provided with each mudguard, the holes on the side arms are mandatory requiring 4 leaving the other 2 for the fork brace (although more could be added if desired) RapidRacerProducts Ltd accepts no liability for any damage / injury caused due to improper fitting / use of our productsSlots and holes for easy installation with cable ties (included) or Velcro straps (sold separately) Finally tighten the bolts to the torque settings below: TORQUE SETTINGS: FOX, MARZOCCH & OHLINS = 1nm | SR SUNTOUR = 2nm Tom didn’t get any shit in his eyes all winter, no glasses, super wet, crazy muddy, nothing on face, it will protect you and your bike from the very worst of conditions Enduro-mtb Magazine review You’ll be treated to a lesson in mud guarding, it offers fantastic protection to the downtube keeping your face clear of grime, the ProGuard is a winter winner IMBike Magazine review

Our special polypropylene mix has been specifically blended for super high impact resistance and cold weather performance: The ProGuard range of mudguards have a matte textured finish with gloss highlights on the logos and centre strip. The underside features a smooth lightly polished finish for better mud flow. Indent to create 4mm of additional tyre clearance (also fits the large raised brace on the Merida e-bike)You can also change the height of the mudguard by 6mm through the slots for more clearance. NOTE: Highest position offers the most stability with the best mud clearance We offer the longer MAX PROTECTION version to be the best protection in the world, this version is 68mm longer at the rear. No other mudguard offers more protection MATERIAL

Slide the guard into position WITH THE WHEEL IN PLACE, you may need to squeeze the sides of the guard as you do so to get it through the sear stays GT85/WD40/Solvents - Only rub these on the surface if you want to remove the gloss and display a matte finish to match your bike. Like most of the formed guards, the Pro Guard has a three-point fixing via the brace and fork lowers. There are 24 crown holes for zip-ties allowing to accommodate a wide range of brace sizes and shapes (although not reverse arch) and it also gets a fork brace indent to increase tyre clearance. It’s compatible with 26, 27.5 and 29inch forks and RRP claims, tyres up to three inch in diameter. The Pro Guard also features seal protection, which simply means the side of the guard is a little bit wider and lower to stop dirt and crud contaminating the seal area, and ultimately ending up inside the lowers. Important - The snap-off hole will break off fast so ensure thre is nothing underneath the guard that the screw driver can hit, failure to do so may lead to damage or harm

The best mounting options

IMPORTANT: You must apply the rubber adhesive side pads to the recess on the mudguard side wings, they protect your fork legs and provide vital stability and resonance damping I have been using the RRP ProGuard on a few mountain bikes for several months. The performance has been excellent, with a vast improvement in the amount of spray and mud that comes off the front wheel reaching the face and body with the most noticeable area when riding at higher speeds where mud can spray out in front, which you would normally ride into it. COMPATIBILITY WHEELS: 26” 27.5” 29” TYRES: up to a 3” tyre BRAKE / OFFSET: MINIMUM 44mm HUB: STD & BOOST FORKS:

The ProGuard is our amazing new range of FRONT and REAR mudguards for disc brake mountain bikes offering unmatched protection from mud and spray, it’s perfect for Trail, Enduro or Downhill racers and essential for the weekend warrior looking for the very best protection. Our design intent was to increase the tyre clearance, improve fit, and reduce the mud clogging issues seen with this type of mudguard. The MINI offers a very compact design for all year round protection, The STANDARD offers superb protection in a shorter more compact design, whereas the longer MAX PROTECTION version (21mm longer at front than the STANDARD and 68mm longer at the rear) offers incredible unmatched levels of protection. Available in 3 sizes Front Mini:We have tested the following chemicals to use on our ProGuards to keep them looking great and shedding mud: