If this happens to you, just untie the knots and tighten the whole rope section again. – Simple! Why you should trust us One of the key advantages of the Nash Fishing Bedchair Buddy is its adaptability. Not only can it be used on your bedchair, but it also serves as a fantastic guest chair or lightweight stalking seat when placed directly on the ground. This elevated seating position keeps you off the damp or cold floor, providing additional comfort during extended sessions. PLEASE NOTE: All services are normally delivered within 48hours but this is not guaranteed as we cannot be held responsible for problems beyond our control. The reason for this is to maintain the flat profile as much as possible and limit sagging within the middle of the bed (also meaning that less central padding is required). To be honest, I was quite surprised at how comfortable the bedchair is without the elasticated midsection. If you also try to move the chair forward to the edge of the bed to get the legs to reach the ground, that does not work either, it still slopes forewards but you also find that you can feel the side of the bed pressing through the updated seat of the chair, and that to is uncomfortableto even attempt sitting in that position.

PLEASE NOTE: (Size restrictions do apply, please see Royal Mail webiste for further information.) All Prices are Inc Vat Firstly it can be used across the middle of a bedchair as a traditional bedchair buddy. This is perfect for when you want to sit up and read a book/magazine or socialise with friends in the bivvy when the weather is bad outside. The unique reinforced rear leg structure simple extends across the bedchair and overhangs the end of it giving you a very firm, and comfortable chair on the bedchair. This will fit practically all bedchairs on the market. In terms of its strength, Trakker claims that the RLX Flat 6 has enough stability for even the largest of anglers. As I said, I’m 13 stone so of average build really. As this Advanta Endurance Reclining Bedchair Buddy is so lightweight, it also makes the perfect guest chair. This is ideal if you’re joined at the bank by another angler, or a friend or family member. After all, it can sometimes be uncomfortable to maintain a conversation over a brew if one of you is stood and the other is sat. This bedchair buddy gives you an easy way of providing a seat to your bankside guest. It also works perfectly as an alternative to a low chair. This is ideal if you’re somebody who enjoys ultra-mobile angling, as this is an exceptionally lightweight solution to the problem of comfortable bankside seating. The size of your bedchair is also vital to a good night’s sleep. Now when it comes to designing a lightweight bedchair, it can be easy for a manufacturer to simply make the whole thing smaller.As we have previously mentioned, the Trakker RLX Bedchair is constructed from a combination of steel and aluminium. I’m not sure exactly where each of these materials is on the frame, but I’m guessing the steel is focused around the areas taking most of the load.

recommend that you use recorded or special delivery as we can not be liable for any loss or damage in transit. The main problem is, the front legs are only about 12", extend by a max of 3" to make about 15" length and the legs angle forward so that reduces the height to 12". If your bedchair is higher than 12" off the ground which mine usually is due to sloping ground, then your screwed, the chair slopes forward and is uncomfortable and useless. I've just got it out of the car now to get the measurements, it's unusable, my bed chair is 16" high off the ground thanks to the slope. As we’ve already mentioned, it’s a decent length and width too so there has been no compromise there. If you have a small car boot or a tight fit in the shed, you might take a look at the Nash Scope Ops 4 Fold Sleep System as an alternative. I’m no longer hunched over after a two day session and to be honest, night fishing has become much more comfortable.

Boats

Overall to summarise the size, you’ll be pleasantly surprised at how large it is considering the light transport weight. Strength & Stability You even have the option of adjusting the roped midsection to suit how firm you would like the bed.

Finally the chair can also be used on its own as a standalone low chair should you wish to sit outside of the bivvy besides your rods or offer a chair to a guest that visits your swim. Due to the angle of the rear leg and also the length of the adjustable front legs you can sit very comfortably in the chair for hours on end. Now given the style of this bedchair, it only makes sense to start by discussing size and weight. Coming in at just under 7kg, the Trakker RLX 6 bedchair is officially one of the lightest bed chairs available on the market.

Bottoms & Joggers

Why they made 12" legs and then only made 3" extensions, I don't know why. I doubt you could make your own extensions as they have a Groove in so they must have to fit a stud inside the frame. It was probably designed in a factory environment on a perfectly flat floor on a bedchair without its legs extended. Don’t let this put you off though. The roped midsection makes up for this and to be honest, any additional padding would only add unnecessary weight. Firstly, Trakker has reduced the padding in the central section of the bed chair, which makes up a fair proportion of the weight of most modern bedchairs. To counteract the loss of comfort here, Trakker has included a roped midsection instead of elastic. A big part of the stability of your bedchair will come from the leg mechanism. The Trakker RLX Compact Bedchair has 6 adjustable legs which can go from 28cm to 38cm. Whilst I find that fine for most of the swims I come across, it may still leave you uneven on steep river banks. That being said, I don’t think there’s any solution to that really. Whilst it is not as comfortable as it’s bigger brothers, Trakker have done everything in their power to reduce the weight without compromising on comfort.