The lock block can be quite small to save on manufacturing costs and if the door has accidentally been hung with the hinge side (the hanging stile) on the swing side, there may be no lock block to find at all! If you are looking for the strongest fixing point possible then the best solution is to attach a batten onto the door and then use this to attach your hooks, hangers or other objects. To allow the construction adhesive to cure and stick the batten to the door you will either need to screw it in place while it dries, take the door off and lay it flat and then put the batten in place or try and clamp it with the door still on. Next, measure and mark both the centre of the door where you want your batten fixed and also the batten itself. These effectively secure the handle and transmit any pulling force to the handle on the opposite side of the door providing a strong and secure fixing.

Plasplugs Hollow Door Fixings 6mm x 23mm 20 Pack - Screwfix

Successfully fixing to a hollow door has always been a tricky job as there isn’t really much to actually fix to as the actual fixing area is very thin.

In this situation the timber for the fixing screws will be very thin giving a poor fixing for the screws to bite. Match up the marks on the door and hanging rail and then use a spirit level to level the hanging rail. Both solutions provide a solid and secure for a variety of items including coat hangers and hooks, toilet roll holders and door handles. For this tutorial we will be using some 2×1 inch planed batten, but you are free to use the correct size batten for your needs. When it comes to actual physical fixings, these are the best fixings DIY Doctor have found for this job.

Hollow Door Fixings 6mm x 23mm 20 Pack - Screwfix Plasplugs Hollow Door Fixings 6mm x 23mm 20 Pack - Screwfix

If your handle fixings either miss or have not secured well into the lock block and become loose, the handle will be loose on the door.Measure and mark the centre point of your batten around 30mm in from either end, drill out two small pilot holes and then countersink them ( see our guide here on pilot holes and countersinking for more information). Screw heads are exposed on the handles and any fixings need to match the finish: Exposed screw heads will likely be 6 gauge raised head countersunk screws where the face is rounded over instead of flat. Insert a piece behind the existing - but a longer piece so you can drill and fix it above and below where the hinge is located. Once leveled up, insert a screw each end and screw up tight to hold batten which adhesive dries out. In the following guide we look at some of the best methods of fixing to hollow doors and ensuring that the object you’re fixing actually stays in place on the door.

Plasplugs Hollow Door Fixings 20 Pack | Wilko - Wilko Site

I put in some hollow door plugs which I thought might help the screws grip better but that has made it worse and the hinge is now coming away from the door. I really like some of your ideas and will give them a go (and then will probably have to get a new door) Ha ha ha!Lay your piece of batten face down and apply several thin beads of construction adhesive across the face of the timber. Fixing screws have pulled out and no longer bite into the timber: Check that the screw has actually been screwed into the lock block and not a hollow part of the door. x Hollow Door Regular Duty Double Fixing Hook for use in Hollow Doors, Thin Skin Partitions, Plywood and Fibreglass. The screw heads will be a close match to the style and finish of a 6 gauge raised head wood screw making it possible to secure your handles in the best way possible and they will look good too.

Which fixings for hinges of hollow door? | Screwfix Community Which fixings for hinges of hollow door? | Screwfix Community

For anything up to the weight of a t-shirt they’ll just about hold but for anything heavier a proprietary fixing needs to be used. For the purposes of this guide we are going to run through two of the above techniques for fixing to a hollow door.Allow 24 hours for the construction adhesive to fully dry and you can then remove the screws and fill the holes over before painting. If your lock/latch does not have these holes then you will likely need to change them for ones that do.