It’s vital that all excess fluid is removed before finishing the job. If too much is left on, or the incorrect colour has been applied to scratches, it can be extremely difficult to remove. Applying T-Cut is a time-consuming process and requires additional care afterwards. If the application of T-Cut is rushed then it can lead to more expensive repairs later on down the line. Common Questions Is T-Cut safe? There are other cases where applying tcut yourself, or trying to repair the scratches yourself, are not recommended. If you are unfamiliar with repairs T-Cut Polish – Removes surface oxidation, minor scratches and blemishes, whilst providing a shiny finish to your paintwork.

Essentially, T-Cut is a good short-term solution, as it will primarily provide your car with a shine. Whilst also removing any light scratches or marks. But this is temporary, as the paint will eventually fade, so a longer-term solution would be a new paint job. For a car with dull and fading paintwork. When Is T-Cut Not Suitable For Use? Regardless of what type of car paintwork you have, T-cut can be used. For some additional uses, it is suitable for our boats, caravans and around the housework. How To Use T-Cut Correctly Deeper Scratches: Whilst it is good for slight, surface scratches, it’s not as suitable for scratches that are deeply ingrained in the paintwork, either accidentally created by scraping against a wall or curb, or deliberately caused by a vandal (if your car is ‘keyed’).

Customers have had varied experiences with the T-Cut Colour Fast 3-in-1 Paintwork Renovator. While some have reported that it did not effectively hide light scratches on their vehicles, others found that it considerably reduced fine line scratches. It is essential to apply the product in a small area and buff it off as you go, avoiding direct sunlight to prevent rapid drying. This process can be applied to a small area of a car, such as a wheel arch, or it can be applied to much larger surface areas. If the latter is the case, then tcut will need to be applied all over, one panel at a time, and will requires several containers of tcut to ensure you have enough of the compound. If, for instance, you want to restore an old paint job all over a car, the process is the same as with a smaller area, but it is a more laborious job. Every panel will need to be treated, one panel at a time, to ensure an even application. The maintenance afterwards will also be more intensive, since the car will regularly need to be waxed all over. T-Cut After Care If You Are Inexperienced With Repairs: You need some idea of what you are doing, as a simple mistake like using the wrong type of cloth, or using one that had accidentally fallen to the ground, can cause more harm than good. Furthermore, knowing when to stop rubbing the T-Cut on the scratch is essential, as overdoing it after the scratch is removed, could result in you revealing the metal beneath the paint. Suitable for all paintwork types, including metallic, this revolutionary paintwork renovator is available in an impressive array of 13 colours. T-Cut Colour Fast not only enriches your vehicle's paintwork, but also cleans, restores, and polishes the surface in a single, easy application, ultimately providing a protective shine that endures.

Where tcut is not suitable, however, is with deeper scratches where it is far less successful, or even places where the car has been dented as well as scraped. It should only be used to rectify light, shallow, surface scratches where T-Cut can be most effective. Keyed car scratches or deep scrapes from a wall or kerb can often be too deep, going all the way down to the basecoat or primer layers of the car paint, for a simple cutting compound to fix. Where this is the case, a stronger method of scratch removal may be needed, and we’ll talk more about this later. How Does T-Cut Work?In fact, ChipsAway repairs all come with a lifetime guarantee, all for less hassle and cost than going to a body shop or garage. In fact, most body shops would repair a scratch by repainting the whole panel, whereas ChipsAway specialists only need to repair the small area affected – and you can keep your car for the day as ChipsAway come to you. If You Rush It Or Don’t Have Time For The Maintenance: As mentioned in step 4, you should always remove any excess product on the car, as it will be tough to remove any that was left over. Since the top, protective layer has been removed, the car now needs to be waxed on a regular basis to prevent corrosion. Waxing is a vital step to remember, as the last thing you want to do, when removing damage from a car, leaves it vulnerable to more damage at a later date. Yes, by removing cloudiness from clear, plastic headlights, T-Cut can be used to restore headlight clarity, which will then result in the visibility of light to increase. This can also be applied to windows and plastic glass, which will enhance the clearness whilst adding a shine. A small amount of T-Cut should be able to remove spray paint from your car paintwork. As with all applications, it needs to be applied very carefully to ensure that further damage is not attributed to the care whilst removing the spray paint. Which T-Cut to use?