To activate your CO alarm, pull the disabling tab out of the alarm and wait up to 1 minute for the green LED to flash to confirm the alarm is active. After 1 minute, press the test button to hear the alarm sound. Please note, the alarm will not sound before the 1 minute activation period is complete. CO alarms and rental properties The alarm features the latest CO sensing technology and can be used to replace end-of-life FireAngel CO-9X alarms. Fitted with a sealed, tamper proof battery that will last the lifetime of the alarm. The sensors within the unit will deteriorate after 10 years, so to ensure you’re protected we recommend you replace the unit after this time. Experience both audible and visual safety warnings with the digital screen, which will change colour to indicate different incident types for clear safety advice.

We have been monitoring it since and I’m pleased to say that the issue appears to have been resolved so no requirement to issue a replacement. We do not recommend a smoke alarm to be fitted in areas where excessive dust or dirt could contaminate the sensing chamber, making it over sensitive. It is also not advised to fit alarms in bathrooms, shower rooms or any other very damp and humid areas, where moisture can cause unwanted alarms. The advice below is purely provided for ‘best practice’ and should not be used independently. Please note, these alarms are not suitable for homes in Scotland under the new Fire & CO regulations.I completed everything that you advised by cleaning any dust on the alarm and banging in the palm of my hand to dislodge anything. WARNING: This alarm will only indicate the presence of carbon monoxide gas at the sensor. Carbon monoxide gas may be present in other areas. Where should I position the CO alarm? Once your CO alarm is activated, this icon or ‘heartbeat’ will continue to flash a green LED in power mode. If a battery fault or warning has been silenced for a period of 8 hours and times out during night time, the silence period will automatically be extended once for a further 8 hours (night silence will increase the counter by 1 for sleep easy). Please note, this feature is not available with the FA3820 or FA3313 alarms. Understanding FA3322 digital display indicators With low level CO monitoring, a pre-alarm warning to open windows helps reduce the risk of CO poisoning and prevents build-up of dangerous CO levels. If a room is not ventilated and ppm levels continue to increase, the alarm will activate. If your alarm is not a sealed battery alarm, then install the batteries following the steps within the manual.

FireAngel’s FA3322 digital carbon monoxide alarm features many icons on the LCD screen. View our guide below to help you understand what each represents. Find out more about the FA3820X4 CO Alarm. FA3313X4: Carbon Monoxide Alarm with replaceable batteries FireAngel recommend a CO alarm is installed between 1 m and 3 m away from each fuel‑burning appliance, as well as installing additional units in areas such as living rooms and bedrooms where you spend most time whilst at home. Activating your new FireAngel CO alarm Ideally, an alarm should be installed in every room containing a fuel-burning appliance and every sleeping room. Additional alarms may be installed to ensure that adequate warning is given for occupants in other rooms, in which they spend considerable time whilst awake and from which they may not be able to hear an alarm in another part of the property.

Read our handy guide for more information on correctly installing your alarms or discover why your Pro Connected alarms may be beeping in our guide. Dust contamination: How do I clean my alarm? Remove the disabling clip by pulling it out of the alarm and retain the disabling tab for future use. Using a soft brush adaptor, your vacuum or your hairdryer on a cool setting, run along the edges and face of the alarm. Please do not use any solvents or cleaners on your alarm as they may cause damage to the sensor or circuitry. Once your CO alarm is activated and tested, choose to install the alarm by mounting on a wall or free standing on a shelf. Your alarm should be placed 1-3 metres away from any fuel burning appliance in your home, in living rooms or bedrooms.

The below provides an overview of installing your carbon monoxide alarm, but please refer to each alarm’s manual for tailored guidance. Which room can I install this carbon monoxide alarm? With a multi-functional LCD digital display and array of exclusive features such as Alarm Memory, Ventilate Instruction, Quiet Self Test and Environmental Sensing, the FA3322X4 offers the highest level of CO detection for your home. The alarm’s high sensitivity mode will be enabled if the alarm predicts CO levels will increase to or above 180ppm for fast reaction to rising CO levels.FireAngel’s new range of carbon monoxide alarms use intelligent sensing technology for a rapid reaction to rising levels of CO. A common cause of nuisance alarms is the incorrect positioning of a smoke or heat alarm. If your FireAngel alarm has begun chirping not long after installation, make sure it is fitted in the right room in your home. The FA3820X4 Carbon Monoxide Alarm offers a variety of safety features, including Ventilate Instruction, Alarm Memory, Sleep Easy and Quiet Self Test.

Where your alarm is installed can also trigger nuisance alarms if not correctly placed, for example too close to doors or windows. Guidance for where to install your smoke, heat and CO alarms can be found below. Tenants, do you know your rights as a renter when it comes to CO alarms in your home? The Government announced its response to a consultation on the use of smoke and carbon monoxide alarms in domestic properties. FireAngel smoke, heat and carbon monoxide (CO) alarms are designed to be as maintenance-free as possible, however there are a few steps that must be followed to ensure your alarms continue to perform correctly. Carbon monoxide alarms in rooms with sloped ceilings should be located at the high side of the room.Alarms located in sleeping rooms and in rooms without a fuel-burning appliance should be located relatively close to the breathing zone of the occupants.