When doors are closed correctly, there is a chance that the centre of the door will only be held in place by the latch, allowing the top and bottom parts of the door to swell or warp in the heat. You can save money long-term by throwing the handle every time you shut the door! If you’ve been affected in this way, take a look at our top tips – they might provide you with a simple solution to the issue! Warping, bowing or swelling That includes removing any dirt from the surface of the door, cleaning around the frame, and even finishing the windows with a glass cleaner. For the final step, you should use beeswax or another similar product to give your newly painted door a protective layer for the materials and a professional finish. All surfaces must be clean, dry and free of dirt, grease, grime and mildew. All waxes, polishes, silicone etc. should be completely and thoroughly removed. Treat any mildew with a 50:50 bleach and water solution. Scrub the solution on to the surface and allow it to stand for 10-15 minutes then rinse thoroughly. Using Polytrol on plastic, gelcoat, tiles, painted surfaces etc.

Clean the surface with warm soapy water and rinse thoroughly or use an appropriate solvent (follow manufacturer’s instructions). Leave the surface to dry for a minimum of 24 hours. Application of Polytrol Colour Restorer General directions Use a brush or a cloth to liberally apply Polytrol. If you notice that some bits are looking shiny and others are looking matt, move any of the surplus oil over to the matt areas. Leave it to work then wipe off the excess Before getting starting with Polytrol, make sure that your door is completely dry. Time to get going… The best way to fix this issue is by adjusting the hinges on the door frame. Start by removing all existing screws from the hinges and then inserting new ones that are slightly longer. This will help create a tighter fit for the door and should stop any warping or bowing. You may also need to add additional weather stripping around the edges of the door if there are still gaps present after adjusting the hinges. Dropped hinges: Applying the Polytrol to a wet surface will not produce the desired effect and could negatively impact the door.

Final Thoughts

You can use Dilunett to remove the previous orange-brown coating, however, Dilunett is powerful enough to remove up to 8 coats of paint in one application, so any other coats of paint that lay underneath the new paint will also be removed. After you have applied Dilunett, your best option is to then finish the doors with a paint, such as Owatrol Deco – our rust inhibiting primer and paint available in 13 colours. NatWest, RBS and Ulster Bank to close at least 172 branches in 2023/24 – here's the full list, plus alternatives CoolSkin is made from a combination of uPVC and GRP (Glass Reinforced Plastic), which offers maximum protection.

Whereas some people will tell you that oil-based paints work best, others will argue that solvent paints are best. Polytrol is a colour reviver and restorer which restores pigments faded or dulled by exposure to the sun. It is a deep penetrating oil that restores the original look and finish to gelcoat, plastic, metal and other surfaces. How do I use Polytrol colour restorer? Phil needed some help restoring his GRP garage door. He wasn’t sure which product to use so he got in touch and asked! We recommended Polytrol as it revives and restores the colour of faded surfaces – it’s grea for fibreglass so perfect for Phil’s garage.Watertight and weatherproof: The doors are airtight and have secondary seals to keep all and any water and air out. Not much can get past these doors. Rather than repainting the whole thing and making a mess, you could invest in a touch-up pen to fill in those grooves and scratches in the door. Anoth customer achieved impressive results on their moped with Polytrol. They just wiped it on with a lint-free cloth, left it to work and then wiped off the excess. The Polytrol brings out the pigment from within the surface and leaves it looking good as new! Polytrol is a deep penetrating oil which restores the original colour and appearance of dull or tarnished plastics, gelcoats, metals, and other surfaces.

It’s important that any rags you have soaked in Polytrol are properly discarded or they could spontaneously catch fire. See Polytrol’s full instructions for more information. It is definitely possible to replace a door without replacing the frame, as long as the door frame is in good shape and the new door panel is the exact same size as the previous one. However, there are some symptoms that may point to the necessity for a new door frame. Not only is our CoolSkin great at protecting materials from all kinds of weather conditions, but it also offers maximum impact resistance. That means there's less chance of the door slab being damaged by bumps.

Although we didn’t have any mildew on the door, if you do, don’t worry. Mildew can be treated with a 50:50 bleach and water solution. Just scrub it on, leave it for 10-15 minutes, then rinse it off. This will help to make sure you remove all dirt, grime, oil and any other residue that may make it harder for the paint to adhere to the surface. The door didn’t take us longer than 20 minutes so we could do it all in one go but if it will take you any longer than 20 minutes, you will need to work within areas that can be completed within this time-frame. Buy your door from EYG and you don’t have to worry about a thing – thanks to our ten-year ‘repair or replace’ warranty promise. In fact, they are particularly resistant to fading, rotting, discolouration, warping, and other kinds of destructive changes that occur in most doors.