b) cable cars where the cabins are lifted and/or displaced by one or more carrier cables; this category also includes gondolas and chair lifts; The lime zest logos are a highlight that grabs your attention. My only colorway suggestion I would make is to have the midsole be white all the way from heel to toe instead of blue halfway through. Steps should be taken to define, on a Community-wide basis, essential human safety and health requirements, environmental protection and consumer protection requirements applicable to cableway installations, subsystems and their safety components. Without this, mutual recognition of national regulatory provisions would create insoluble political and technical difficulties as regards interpretation and liability. By the same token, standardisation without prior definition of harmonised regulatory requirements is not sufficient to solve the problems. Where a Member State considers a safety component or subsystem referred to in Annex I to have been designed or constructed using an innovative approach, it shall take all appropriate measures and may make the construction and/or putting into service of an installation in which such innovative components or subsystems are to be used subject to special conditions. It shall immediately inform the Commission thereof, stating its reasons. The Commission shall immediately refer the matter to the committee provided for in Article 17. if applicable, the technical documentation of the approved type and a copy of the EC type-examination certificate.

the means to monitor the achievement of the required component quality and the effective operation of the quality system.the quality records as provided for by the manufacturing part of the quality system, such as inspection reports and test data, calibration data, qualification reports of the personnel concerned, etc. The manufacturer must lodge an application for assessment of his quality system with a notified body or his choice, for the components concerned. b) affix the CE conformity marking on the safety component and, on the basis of the modules laid down in Decision 93/465/EEC, draw up an EC declaration of conformity in accordance with Annex IV. Any decision taken pursuant to this Directive which restricts the use of safety components or of a subsystem in an installation or the placing on the market thereof shall state the grounds on which it is based. Such a decision shall be notified at the earliest opportunity to the party concerned, who shall at the same time be informed of the legal remedies available to him under the law in force in the Member States concerned and of the time limits to which such remedies are subject.

In the absence of European specifications, the technical specifications should as far as possible be defined by reference to other standards in use in the Community. Main contractors may define the additional specifications needed to supplement the European specifications or other standards. These provisions must ensure that the harmonised Community-level requirements with which cableway installations must comply are satisfied.

Stability And Good Fit

The EC procedure for examining subsystems shall be carried out at the request of the manufacturer or his authorised representative established in the Community or, in their absence, any natural or legal person who places the subsystem in question on the market, by the notified body referred to in Article 16 which the manufacturer or his authorised representative or the abovementioned person appointed for that purpose. The EC declaration of conformity shall be drawn up by the manufacturer or his authorised representative or the abovementioned person on the basis of the EC examination in accordance with Annex VII. In the light of the committee's opinion and following consultations with the committee set up pursuant to Directive 98/34/EC in the case of harmonised European standards, the Commission shall inform the Member States whether or not it is necessary to withdraw the European specifications in question from the published information referred to in paragraph 3. the measures relating to a subsystem are unjustified, it shall immediately so inform the manufacturer or his authorised representative established in the Community or, in their absence, any natural or legal person having placed the subsystem in question on the market, and the Member State which took the measures. All components must be available for verification in the form of homogeneous lots. A random sample must be drawn from each lot. Components in a sample must be individually examined and appropriate tests as set out in the European specification(s) referred to in Article 2(2) of this Directive, or equivalent tests, shall be carried out to ensure their conformity with the requirements of this Directive and to determine whether the lot is accepted or rejected.

The applicant must inform the notified body that holds the technical documentation concerning the EC type-examination certificate of all modifications of the approved component which must receive additional approval where such changes may affect the conformity of the component with the essential requirements for the prescribed conditions for its use. This additional approval is given in the form of an addition to the original EC type-examination certificate. Additionally the notified body may pay unexpected visits to the manufacturer. During such visits the notified body may carry out or cause to be carried out, tests to verify that the quality system is functioning correctly, if necessary. The notified body must provide the manufacturer with a visit report and, if a test has taken place, a test report.The control devices must be designed and constructed so as to be safe and reliable, to withstand normal operating stresses and external factors such as humidity, extreme temperatures or electromagnetic interference and so as not to cause dangerous situations, even in the event of operational error. The other notified bodies may receive copies of the EC type-examination certificates and/or their additions. The Annexes to the certificates must be kept at the disposal of the other notified bodies. Implementation of the essential requirements, particularly with regard to the safety of the installation, and coordination of all procedures call for the establishment of a committee. Member States shall, for a period of four years following entry into force of this Directive, allow: