Model above is for basic on/off switching. Choose an optional control module to upgrade fan for Pullcord, Pull cord with adjustable timer, Humidity, pull cord with timer overrun, motion sensor with timer overrun, Motion sensor/humidity/timer . Don’t forget to add the control module you want. Only low voltage module fits low voltage fans. It/s so iCON easy Applications: The Airlfow Icon 30 fan is very powerful. With an extract rate of 32 litres a second, it meets the building regulations for bathrooms, kitchens and utility rooms.

Finally, if you think you (or anyone else in the house) will forget to turn the fan on, consider a model with a humidity sensor. This automatically activates the fan when the level of moisture in the air exceeds a certain threshold. This sensor may need occasional cleaning, though, or the accumulation of dust or grime will hinder its effectiveness. What about noise? With an air extraction rate of 118m3/h, the Icon 30 is perfect for installing in a high use bathroom and meets building regs for utility room installations. The precise duration of the overrun is normally configured during installation, with most fans offering a range between 30 seconds and 30 minutes. You might as well tend towards the latter end of the scale as the cost is very low: on average, a fan like this uses around 8W. These come in a variety of combinations shown here - each of which are available for both standard voltage and SELV fan models.

Specification

Model above is for basic on/off switching. Choose an optional control module to upgrade fan for Pullcord, Timer, Humidity or Motion Sensing operation. Don’t forget to add the control module you want. Any module fits any fan. Its so iCON easy! Applications This standard 30 model (72591601) is suitable for installation into zone 3 of the bathroom and offers basic on/off switching. Choose an optional control module to expand the functionality and automation:Pullcord, Timer, Humidity or Motion Sensing options. The largest fan in the range, the 150mm/6” Icon 60 Kitchen unit can also be surface or flush mounted as desired and with an air extraction rate of 260m3/h, the Icon 60 is a perfect stylish addition to any domestic kitchen.

The Airflow Icon range is a great looking axial extractor fan which thanks to its eye-catching 'opening iris' shutter, has become a modern design classic. Tiling is a breeze with the circular cover flange, reducing the need to 'make good' and one wipe and the cover is clean. Please note: While the Icon 30 uses 4" inch ducting it does require a 6" hole in the wall or ceiling for flush fitting.Most domestic bathroom extractors attach to a 100mm hole in the outside wall. If you’re replacing a standard-sized extractor fan, this hole will already be present and you should be able to install the new one yourself. Before you remove the old fan, it’s a good idea to take a photo of its wiring for later reference – and make absolutely sure you shut off the mains power before you take the old one’s front housing off.

Each fan in the range has a slot to insert a control module of your choosing, including options for pull cord, over-run timer, Humidistat and Passive Infra-red PIR sensor. The ICSTT model features an over run timer which keeps the boost setting running for 2 / 15 / 30 / 40 minutes. With an air extraction rate of 76m3/h, it easily surpasses building regulations for bathroom installation. Easy to install due to the core drilled hole and its twist on/off cover enabling it to be fitted and fixed easily with its single side entry fixing screw.In a survey carried out by ventilation specialist Vent-Axia, 40% of respondents said that they or their children had been woken in the night by a noisy bathroom fan. Even the cheapest fans are usually very quiet out of the box, but as the motor bearings start to wear – typically after about two years with low-end models – the blades can start to oscillate against the main housing, producing an annoying rattle in the process. A higher-quality fan should last longer, but if you value quietness then at some point you’ll probably need to repair or replace your fan. How do you install a bathroom extractor fan? The PureAir Sense comes with two spigots (or sleeves): one for standard 100mm installation and another for larger 125mm portals. The larger spigot is the one to fit if you want to benefit from its excellent 39l per second flow rate. That said, its standard 32l per second flow rate is still better than most and easily good enough for the majority of bathroom installations. PRHTM - Infrared - Passive infrared activation with adjustable humidity setting and adjustable timer overrun

The ICON30 comes complete with cantilever fixing lugs enabling a recessed installation on uneven surfaces.

Blow off some steam, banish damp and wave goodbye to condensation with our favourite bathroom extractor fans for every budget

The 100 mm/4” Icon 15 Bathroom unit can be flush mounted in either the wall or ceiling and with a low-profile fascia, sits unobtrusively in any room. The more powerful and slightly larger Icon 30 Bathroom & Utility room unit can be installed similarly to the Icon 15 either as a surface mounted 100mm/4” fan or flush mounted as a 150mm/6” install by removing the rear cowl. The Airflow ICON30 72591601 ventilation fan is suitable for fitting into walls or ceilings in areas such as shower rooms, bathrooms, en-suites and toilets. This really is an excellent extractor that uses just 2W of electricity when running continuously and no more than 5W at full pelt. It’s also one of the most attractive models around – the fascia can be used bare or with the included white magnetic cover – and one of the very quietest.