A new function which appears during automatic configuration for certain ECUs . Following a successful automatic configuration, a new screen appears displaying the ECU parameter values which were modified during the operation. It is compatible with most Peugeot cars from 1995, but it can not work well with Peugeot 307 after the 2004 year. Read Fault Codes :Displays all stored and pending fault codes with complete description (e.g. "Rail pressure - too low pressure").Program supports report printing or copy to clipboard.

Lexia 3 with Diagbox V7.57(item SP08-C)is the best lexia diagnose toolamong all the lexia 3 we sell on the shop. It hasoriginal 921815C chips inside, and itis alsofully compatible with Peugeot 307/C5. Displaying of a screen for viewing the ECU parameters changed during the automatic configuration operation.Citroen: C1, C2, C3 DS3, C4, DS4, C5, C6, C8, C-CROSSER, NERO, BERLINGO, JUMPY, AX, SAXO, BX, ZX, XSARA, XANTIA, XM, EVASION, C15, C-ZERO etc. Q4: Can Lexia-3 PP2000 (item NO. SP08-C) work with Peugeot 407 2005, after install the NEW DPF, can I reset DPF counter? After Eolys is full, can I reset Eolys counter? Lexia 3 Revision B Kit - Usually for cars up to 2022 and not suitable for Peugeot 307 and C5 after 2003 however does vary on ECU.

This information has been collated from available sources on the net into a consistent format. There may be some versions where a change log could not be sourced. Diagbox Version 6.39 / 7.06 PCB edge is golden with original full chips. Double PCB has 7pcs optocouplers, which are 100% original and new. Incidents corrected :– Correction of the problem of communication with the EDC17C10_BR2 ECU for the Peugeot Partner and Citroën Berlingo (B9) vehicle – Correction of the impossibility of manual configuration on the ESP 8.0 ECU for the Citroën C4 (B5) vehicle – Correction of the diesel additive and PEF personalised maintenance on the SID 807 ECU for the Citroën C4 Picasso (B58) vehicle – Correction of the programming of the keys on the BSI 2010 ECU for the Citroën DS4 (B75) vehicle – Correction of the programming of the hands-free identifier on the BSI_2010 ECU for the Citroën DS5 (B81) vehicle – Correction of the access to the manual configuration menus on the RT6 ECU for the Citroën DS4 (B75) vehicle – Correction of the impossibility of manual configuration on the BECB ECU for the Citroën C4 (B7) vehicle Auto-Scan (Complete Car Scan/Test) :Detects all ECUs (electronic control units) installed in car and reads all diagnostic fault codes. Citroën C4 Picasso (B78)2. New features :– Addition of the V46.21 engine ECU for the Citroën C4L China (B73 China) vehicle – Addition of Brazil and Argentina for the functionality of a new vehicle – Addition of the side panel for navigation in DiagBox (see doc attached)Our diagnostic interface Lexia 3 contains K-Line multiplexor, CAN-BUS interfaces and SAE J1850 bus (both PWM and VPW). Please setup the software according to the requirements to hardware and software. Otherwise it will fail to setup and take you much trouble. Lexia 3 Diagbox dealer diagnostic tool contains K-Line multiplexor, SAE J1850 bus (both PWM and VPW) and CAN-BUS interfaces. Update 8.14, available from 08/09/2015, includes corrections, in particular DiagBox symptom corrected

Manual resuming of the automatic configuration: displaying of a manual configuration screen when certain parameters could not be configured during the automatic configuration procedure. Diagbox 8.55 (v07.855) Multilanguage| 09/2017 (20 languages:Chinese, Croatian, Czech, Danish, Dutch, English, Finnish, French, German, Greek, Italian, Japanese, Hungary, Polish, Portuguese , Russian, Slovenian, Spanish, Swedish andTurkish) integration of the 3 air conditioning assessment charts Chart 208 2008 Europe, charts M3M4 and generic charts. The help messages on the automatic configuration Before/After screen (filter activated/deactivated) are no longer inverted if the parameters are modified. To change the Firmware version, rename the desired Firmware file from APPLI_X.X.X.COM to APPLI.COM.Read Identification :Displays complete identification of control unit, e.g. part number, software/hardware version, manufacturer, etc... Displays complete identification of control unit, e.g. part number, software/hardware version, manufacturer, etc... Do not forget to restart the PC and restart diagbox after each update to finalize it, otherwise your diagbox will not run. Multi-language: English, German, French, Japanese, Russian, Spanish, Portuguese, Swedish, Turkish, Dutch, Polish, Italian, Hungary, Greek, Czech.