To the main body, let's assemble the funnel binder, which is also the identity of Nightingale. This is the exterior and base parts. Fit the base part into the exterior part. Connection joint with the main body. Thanks to this part, the binder can move flexibly. The holding power is perfect. We will attach the vernier to the base part. It is a masterpiece that all the yellow parts are color-coded by the vernier internal parts. The funnel base parts are set on the surface. This is also a fine detail. This is the funnel. It is a one-part configuration. Of course it is removable. If you attach the funnel, the funnel binder is completed. Now, the parts other than the armament are finally completed. A little after. The abdomen can move up and down. The mega particle cannon can be exposed by moving the abdominal parts. This is Bandai's highly detailed plastic model kit which self assembly is required. No glue or paint necessary. Official product visuals shown are provided by Official Bandai which may be painted and clear coated. Final product may be slightly different upon completion. This product a highly detailed plastic model kit which self assembly is required. No glue or paint necessary. Official product visuals shown are provided by the officials which may be painted and clear coated. Final product may be slightly different upon completion.

FA-93HWS ν Gundam Heavy Weapons System Type | RX-93 ν Gundam Double Fin Funnel Type | RX-93-ν2 Hi-ν Gundam Let's start with the contents of the box. The instruction manual is also extensive with setting explanations. The Runner is a multi-color molded A runner. The new effect parts are beautiful. B runner. The shield and crotch parts are conspicuous. C runner. It is a runner for the exterior of the legs. D runner with outstanding presence. Nightingale's landing gear can be interchanged into two different specifications depending on your preference.For better results, most or some of the details are needed to be applied/panel-lined with Gundam Markers and/or Mr. Color paints. The included Beam Rifle also serves as an add-on for the builders that intend to complete the Ballistic Zaku ( HGGTO MS-06S Zaku II/ HGGTO MS-06S Zaku II (Red Comet Ver.)/ HGUC MS-06S Zaku II Commander Type Char Aznable Custom (2020) + HGBC Ballistic Weapons) model kit build, though the rifle is much larger than the one seen in the ONA.

Five Funnels were equipped on each of the movable binders, resulting in a total of ten funnels. They were resized Funnels from the NZ-333 α Azieru, and had high operability due to the adoption of a large-capacity condenser system [2].. The landing gear of the rear skirt can be replaced and the shaft can be moved to reproduce storage and deployment. The propellant tank can be deployed with a movable ball. NOTE :หากสั่งสินค้าพร้อมส่งกับสินค้าพรีออเดอร์ในบิลเดียวกันจะรอจัดส่งพร้อมกันเมื่อสินค้าพรีออเดอร์มาครบแล้วนะคะ In case the product, there may be cases, under certain situations, where the delivery date is changed or delayed ,we, VCAGUNDAM.com cannot take responsible for any loss or detriment involved in the use of the service. Most of the red exterior is under-gated as shown in the photo, so the gate marks are not noticeable. I attached the exterior of the knee and the front sneaker. The armor of the front sneak can be flipped up. Sneak exterior. There are three engines inside.Each part of the base of the funnel binder is movable, and the binder can be unfolded and folded. The funnel can be removed individually. The crotch part is completed when combined. By the way, the crotch part can move up and down a little. I tried to match the parts assembled so far. Thanks to the movable claws, the ankles touch the ground comfortably. The Legs joint axis of the ankle has a large diameter, so the strength is outstanding. The sealing part has a seam in the center as shown by the red line in the photo. This is one of the few parts that needs to be erased. If you attach the base parts of the rose-apple, the leg frame part is completed. Depending on where you live, the time it may take for your exchanged product to reach you, may vary.

The MA class giant is reproduced in detail on 1/144 scale. Left and right width about 400 mm, total height about 211 mm. Gundam #Gunpla #โมเดล #โมเดลกันดั้ม #โมเดลกันพลา #กันดั้มกันพลา #โมเดลgundam #โมเดลgunpla #gundamโมเดล #gunplaโมเดล #vcagundam #vca The assembly of the arm is very simple parts division. The base parts of the wrist are also nicely detailed. There are 6 types of hand parts: left and right fists, left and right saber handles, right gun grip, and left flat hand. The movable range is also very excellent. The movable range is a little narrower than usual, but you can also bend it so-called. Nightingale can mount onto Action Bases 1 or 4, though it requires an extra arm unit from an additional copy to support its weight. Barder, Ollie (2018-11-05). Yutaka Izubuchi On Designing The Most Popular Gundam Ever And His Love Of Kaiju.

No Painting Required

PLEASE TAKE NOTE THAT THE PICTURES DESCRIPTION BELOW ARE FOR REFERENCE ONLY. IT MAY BE DIFFERENT FROM THE ACTUAL PRODUCT.