LZV100 is designed to manage overload conditions, owners shoud be aware that whenever it is set to reduce the The display (and scooter) can be powered on or off by pressing and holding down the red power button. Odometer and Trip The entries that you must make using the LH100 keys are shown on the left. In the middle you will see what is shown on the display after the keystroke. To the right a brief explanation is provided. devices to enable a personal computer (any flavour) to connect to Xpressnet. I chose the Ethernet interface (23151) for a couple now change the speed and direction that the displayed locomotive resume with when the layout is turned on again...

Battery error code 6: Battery has been discharged below the acceptable voltage threshold. The cause could be the scooter has been sitting around too long and discharged below the threshold or the undervoltage threshold has been set too low. You can look up the correct undervoltage settings for your scooter in our settings database.Insert the 5-pin DIN-connector into a LA152/153 connection plate that is connected to SET02 or Atlas Commander, or to any other XpressNet 5 pin DIN plug.

The locomotive decoder's speed step mode (set via CV29) must match the LH100 number of throttle–positions ( Öp.42 ). If the function is set to momentary activation, then it is only turned on for as long as the key is pressed. The display shows accordingly. The speed of travel of the locomotive is controlled with any one of the four following operation keys. The QS-S4 is designed in such a way to be compatible with a wide range of electric scooters (and even e-bikes) that operate on different voltages, with different motors and tire sizes (among other things). When the arrow is up the locomotive goes forward. When the locomotive points down the locomotive will

This operation manual is intended to make using the LH100 easy for you. To get started, first read the section “First Steps". After you have understood the basic locomotive control, you can familiarize yourself with the full range of functions of this hand held controller step by step and put them to use. Wire Electric Bicycle Controller With Lcd Display Meter 24v 36v 48v 350w Motor Brushless Kit For Scooter Mountain Bike Com

Lh100 Electric Bicycle Lcd Meter And Controller 250w 350w 6 Brushless Bike Kit Accessory Rainproof For Modification Com This LCD throttle interfaces with the controller and battery and should not to be confused with being a controller itself — a beefier component buried deeper with the electric scooter. The QS-S4 provides a readout of speed, odometer, trip, mode, and battery remaining. It features buttons that allow you to power your scooter on, control the lights, and adjust a cryptic list of electric scooter settings known as p-settings or program settings. These settings dictate everything from regenerative braking strength to max throttle power to motor pole configuration. If you’re looking for specific settings for your electric scooter, see our database of electric scooter p-settings. have my layout hard-wire tethered at all. I effectively have my Xpressnet set up as a Wi-Fi client connecting wirelessly to

In this large section you will find out: what "programming" really is in Digital plus by Lenz ® what settings can be changed by programming what different methods can be used for programming how you proceed when programming Headlight error code 13: This error code is related to the LED lights on your scooter. The connection may have come loose, or the LED itself has been damaged. To troubleshoot, you can test the LED with multimeter set in diode test mode. P-settings allow scooter riders to customize their ride. The top 5 programmed features in both types of LCD finger throttles are: Moreover, the LH100 6 wiring schematic provides detailed instructions on how to wire the motor control system correctly and safely. For instance, it provides detailed instructions on how to connect all the motor control components, including the motor, power supply, battery, encoder, and switches. It also provides helpful tips on troubleshooting any issues you may encounter, and it outlines the various safety measures you should take when operating the motor control system. The LH100 can be connected to any XpressNet system including the following components of the Digital plus by Lenz ® system: