The HydroForce Series 3 is a high-quality pump for use under water or surface use in or with rainwater harvesting tanks. The Hydroforce Rainwater Harvesting pump is an electronically-controlled, pressure-sensitive, centrifugal roto-dynamic pump with no reciprocating parts. The pumps have their pressure and flow rate tested twice at different stages of assembly. the performance being inserted to hold the pressurised zones together. A system has been put into place to automatically Alloy bulkhead, pressure release gap & twin chamber design prevents ingress of water to the motor, electrical components & to bearing oil All components used within the pump have been sourced with the ground rules that quality is the important

Alloy bulkhead, pressure release gap and twin chamber design prevents ingress of water to motor, electrical components and to bearing oil. of each pump is automatically logged against its bar code number to assure the client of its quality. At the factory in Peterborough each pump is tested individually, pumping water through a pre-determined cycle to ensure performance is to spec, and the performance of each pump is automatically logged against its bar code number to assure the client of its quality. SpecificationsSee below for an overview on the HydroForce™ Series 3's development and high quality manufacturing. The material itself is the highly corrosion resistant 70L aluminium- then anodised to further guarantee New: Inlet strainer and output pipe connector are factory-fitted and the seals tested to ensure proper running of the pump. As with other submersible pumps, it is obligatory to prime the pump by removing the filler screw and filling the body of the pump with 2 litres of water, then replacing the filler screw.

The exterior bodywork is an Italian-styled shape which is stable in the floor of a water tank. The pump and electrics are totally new, engineered to give more reliable underwater performance. Now an alloy bulkhead, pressure release gap and twin chamber design prevent ingress of water to motor, electrical components and to bearing oil. and twin chamber design prevent ingress of water to motor, electrical components and to bearing oil.New: Alloy bulkhead, pressure release gap and twin chamber design prevents ingress of water to motor, electrical components and to bearing oil. At the factory in Peterborough, each pump is tested individually, pumping water through a pre-determined cycle to ensure Logic processors in PCB prevent other pump anomalies and permit factory programming of reset timings. The HydroForce™ Series 4 is an electronically-controlled, pressure-sensitive, submersible, centrifugal roto-dynamic pump with no reciprocating parts.

Inlet port 1 inch (25mm) female BSP. Output port 1 inch (25mm) female BSP provided with a push-fit connector for 1 inch (25mm) MDPE pipe. performance is to spec, and the performance of each pump is automatically logged against its bar code number to assure prevents ingress of water to motor, electrical components and to bearing oil.) This componant alone went Inflating a paddle board requires a pump that provides air with high levels of pressure so you can inflate your board in a reasonable amount of time and get into the water as soon as possible. Browse our range of Decathlon SUP pumps including manual and electric paddle board pumps to find your fit. Decathlon SUP PumpsThe pump features a self-controlling pressure switch, dry run protection and a non-return valve. It is suitable for total immersion in tank water or it can be externally connected to the tank above ground. The HydroForce™ Series 3 is an electronically-controlled, pressure-sensitive, submersible, centrifugal roto-dynamic pump with no reciprocating parts. Get ready for adventure with the Hydro-Force™ Oceana Convertible Stand-Up Paddleboard Set. This is an all-round board stand-up paddle board and kayak hybrid that offer the best of both worlds. It is the perfect shape for safe and multifunctional flat water and small wave riding, and it can be easily converted into a kayak with the included seat and footrest. The Series 3 will deliver up to 3.5 bar (household pressure is around 2.5-4.0 bar). If connected to a hose or tap, the For example the patented plate is manufactured by a process of high pressure aluminium die casting. This

pressure switch, dry run protection and a non-return valve. It is suitable for total immersion in the water tank or it can beThis SUP is constructed with drop stitch material where thousands of fibers connect the top and bottom of the board. This provides exceptional strength and rigidity, similar to a hard-sided board, while still keeping it lightweight, portable and easy to store. A great all-rounder this SUP has a shape that ensures great stability and speed in every water condition. Supplied with the ultra-lightweight adjustable 4-piece aluminium paddle, you can set it up to suit your paddling style.