Hanging a plant hook using a ceiling joist is the most secure way and the safest, especially if you plan to hang a heavy planter. Materials: Unfortunately, I have no idea about what specific kind of drywall plate it is or how it was attached; at any rate there is only a fixed place that I can hang the plant from so that it doesn't prevent me from opening window. Use an electric drill to drill a pilot hole into the ceiling joist. The pilot hole will allow you to screw the hook screw into the ceiling by hand without it binding up or breaking [5] X Expert Source Gino Colucci Select a drill bit that is about the same diameter as your hook screw's threaded shaft, but smaller than the outer threads themselves. A toggle bolt cannot be screwed into a wooden joist, so make sure you're drilling into a hollow area.

drywall ceiling? How much weight can I hang from a drywall ceiling?

When attached, simply bring the board up and along until the clamps align and clip together. The plasterboard can then be gently pushed (hinged) upwards and is it automatically square with the joists.

Instructions:

Metal spring toggles offer the best support for hanging on a plasterboard wall. The metal toggle is squeezed flat and pushed through the drilled hole in the plasterboard. Once it is behind the plasterboard, the toggle springs open and the two wings pull flat against the inside face. As the supplied machine screw is tightened, the wings are pulled tight against the inside face and spread the weight of the load. When using spring toggles, you will need to remove the spring part from the machine screw and then pass the screw through whatever you are fixing (cabinet, etc) before re-attaching the spring toggle and pushing it into the hole in the plasterboard.

Ceiling Board Hanger - The best way to install plasterboards

I have previously attached shelves and all kinds of things to drywall WALLS, no problem, and also reading here I mostly found about attaching/hanging things to/from walls, too, but I am a bit concerned about how much would a drywall plate be able to hold something hanging straight down from it. The clamps will allow one person to hold and align the panels in position – saving on expensive double-labour costs associated with this type of work. Plasterboard Fixings– When hanging anything heavy from a plasterboard wall, it is always better to use more fixings than you might normally need. Using four plasterboard fixings instead of, say, two fixings, will greatly help to spread the load of the wall unit, shelf, etc, and therefore reduce the chance of the fixings pulling out of the wall. These relatively new plasterboard fixings are available in a variety of colours, each capable of holding different maximum weights. These range from blue (113kg) to yellow (71kg). GripIt fixings work by having three separate loading points, dispersing the weight of the object being held better than many traditional fixings. They are only really suitable for use in places where they will be hidden behind the fixture. A large hole needs to be drilled, and the GripIt sits flush at the edge and is clearly visible. You can find out more about GripIt fixings here. If you must hang your ceiling hook in a location where there is no joist, use a toggle bolt, also known as a toggle "anchor," with a hook. [6] X Expert Source Gino ColucciIf you have a crawl space or an attic with exposed joists, look to see which direction the joists are laid and also how far apart they're spaced. Locate the nearest ceiling joist where you want to hang your hook. A joist is one of the beams that supports a ceiling, and it's the securest place to fasten a hook. The easiest way to locate your ceiling joists is by using a stud finder [2] X Expert Source Gino Colucci DIY Extra is an ever-growing collection of Do It Yourself guides, projects, tutorials and articles covering many aspects of DIY and Home Improvements. Cavity fixings work in a similar way to plastic or poly toggles. They are pushed into a pre-drilled hole and then the action of the machine screw turning in the fixing spreads four wings outwards to grip against the inside face of the plasterboard. Most cavity fixings have a toothed flange to grip the outer surface of the plasterboard. This needs to be pressed firmly into the surface of the plasterboard to stop the fixing turning as it is tightened. Do you have attic access above the spot on the ceiling? I would try to toenail a cross piece perpendicular to the ceiling joists where you want to hang your plant. If there isn't room to swing a hammer between the joists and rafters that close to the edge of the roof, you could just screw into the end of the cross piece through the joists with 3" wood screws.

Hooks M6, Plasterboard (Pack of 4 pcs) Wing Spring Toggle Hooks M6, Plasterboard

There are a few different methods to install a ceiling hook to hang a plant from, but this post is going to cover two of them. The first method involves finding a joist, and the second method uses a toggle bolt. Don’t let the words “joist” or “toggle bolt” worry you though, both of these methods are very easy, and require few tools. Read on for instructions for two ways to install a ceiling hook.All plasterboard fixings are designed to do basically the same thing: Increase the area of the plasterboard which is put under stress by the object hanging from it. However, not all of them do this in the same way and not all of them are suitable for all applications. As a general rule, use plastic or metal screw in fixings for light loads, plastic anchor or spring toggles for medium loads, and metal spring toggles for heavy loads. Plastic Expanding Anchors Our revolutionary new plasterboard hanging tools offer a number of significant benefits when undertaking the extremely difficult task of fitting plasterboard to joists and existing ceilings. Take particular care to drill accurately sized holes when using poly or nylon toggles. Plastic or nylon poly toggles are suitable for light to medium loads such as lighting fixtures. Poly-toggles or nylon toggles work in a similar way to the plastic expanding anchors above. Metal Spring Toggle H and screw the hook into place until it is flush against the drywall. (If it becomes too difficult to turn, you can put a screwdriver into the hook to use for leverage.)

15kg White Small Swivel Ceiling Hook - Bunnings Zenith 10 / 15kg White Small Swivel Ceiling Hook - Bunnings

A neat and strong, all-in-one plasterboard fixing. These are available in a variety of types, with standard screw heads, as well as hooks and loops. This makes them good for hanging things from a plasterboard ceiling. They are also available in a range of sizes. A hole is drilled that matches the width of the unexpanded plastic sheath. The expanding anchor is pushed all the way into the hole and then tightened by turning the screw, hook, or loop. As the screw tightens, the plastic sheath spreads until it is tightly pulled against the inside face of the plasterboard.If you have trouble twisting it through the last few rotations, grasp the hook gently with pliers and use the pliers to gain added torque. These plasterboard screws combine a metal or nylon plug with a screw thread for the fixing screw. They vary in size and length but they all have the deep outer thread in common. The deep thread is designed to give a much better grip on the plasterboard, whilst also spreading the weight of the object they are holding up. Suitable for light loads and plasterboard in good condition. Plasterboard Plug Assess the weight of the suspended item. Estimating the weight of the item you want to hang from the ceiling will determine what size fastener you need. Hanging a paper lantern will require a different fastener than hanging a large, heavy pendant lamp.