In mathematics, a fraction is a number that represents a part of a whole. It consists of a numerator and a denominator. The numerator represents the number of equal parts of a whole, while the denominator is the total number of parts that make up said whole. For example, in the fraction of 3 SYNERGY is designed with a low initial polymer load, abluminal coating and bioabsorbable polymer which may reduce the risk of thrombosis and the need for prolonged dual antiplatelet therapy. Fraction subtraction is essentially the same as fraction addition. A common denominator is required for the operation to occur. Refer to the addition section as well as the equations below for clarification. a Schmidt W, et. al. Direct comparison of coronary bare metal vs. drug-eluting stents: same platform, different mechanics? Eur J Med Res. 2018 Jan 8;23(1):2. doi: 10.1186/s40001-017-0300-y. PMID: 29310720; PMCID: PMC5759296. When a is a fraction, this essentially involves exchanging the position of the numerator and the denominator. The reciprocal of the fraction 3

It also plays a role in determining the length of engagement. UN: standard series thread. UNC: coarse thread series. UNF: fine thread series. UNEF: extra-fine thread series. UNS: special thread series. UNR: standard series thread with rounded root. (This series is number of thread that would fit along a one inch length. thread series designation:(UN, UNC, UNF, UNEF, UNS) The thread series is generally relative to the outside diameter of the screw. 20

Computing

Glossary Thread calculator: All calculated results are based on; Basic outside diameter, number of threads per Yamaha Niken runs a 17″ rear but two 15″ fronts. The 15 inch tyres you put on a Tmax 500 are H rated and so you can’t run these on the Niken as it needs a V-rated tyre. Bridgestone are the OE tyre supplier for the Niken and at the moment the only tyre you can run is the Bridgestone A41 and while other tyres will fit you won’t get a matching set of 15 and 17s. Scooterwise, the 16-incher is a common fitment. Bikes like the Honda SH125i and SH300i run a 16-inch front and rear. The NSC110 Vision runs a 80/90/16 front and a 14-inch rear.

Honda CB125F 2015 to current runs an 80/100/18 front and 90/90/18 rear. Pan European ST1100 and ST1300 both run an 18 inch front. Other notable bikes over the years are the TDM850 and 900. Pictured above is a Ducati Scrambler and these run an 18-inch front. Yamaha’s 2007 to 2017 YBR125 ran an 18-inch front. screw thread (This series is not supported) Class tolerances:(If unsure, use class 2A for external or 2B for internal) Tolerance classes 1A, 2A and 3A apply to external thread Tolerance classes 1B, 2B and 3B apply to internal threads. The class tolerance determines the size of the gap between the pitch diameters ofsize of the "V" shape of the helical portion of a thread. NOTE: If the length of the threaded portion of a screw or threaded hole is diameter of a Screw or the biggest internal diameter of a threaded hole. NOTE: The size of the hexagon of a bolt or nut has no relevance when defining Scooters are slightly different and they range across a larger amount of tyre sizes due to the fact they come in far more shapes and sizes, often with the front and rear rims in different diameters. of thread series, pitch and diameter. (Not to be confused with the length of a thread) V-Shape: Pitch: The distance between 2 adjacent "V" shapes. Real pitch: The distance between "V"s after following a helical path around the History/origin: The term "inch" was derived from the Latin unit "uncia" which equated to "one-twelfth" of a Roman foot.

turn. Definition: This is the standard way of defining a screw thread. example: 7/8-18 UNS 2A 2 starts 7/8: Basic outside diameter. Can be a fractions, screw number In engineering, fractions are widely used to describe the size of components such as pipes and bolts. The most common fractional and decimal equivalents are listed below. 64 th

Inches to Millimeters Conversion Formula

the numerator is 3, and the denominator is 8. A more illustrative example could involve a pie with 8 slices. 1 of those 8 slices would constitute the numerator of a fraction, while the total of 8 slices that comprises the whole pie would be the denominator. If a person were to eat 3 slices, the remaining fraction of the pie would therefore be 5